This paper investigates the potential benefit of ground-based microwave radiometers (MWRs) to improve the initial state (analysis) of current numerical weather prediction (NWP) systems during fog conditions. To this end, temperature, humidity and liquid water path (LWP) retrievals have been performed by directly assimilating brightness temperatures using a one-dimensional variational technique (1D-Var). This study focuses on a fog-dedicated field-experiment performed over winter 2016–2017 in France. In situ measurements from a 120 m tower and radiosoundings are used to assess the improvement brought by the 1D-Var analysis to the background. A sensitivity study demonstrates the importance of the cross-correlations between temperature and specific humidity in the background-error-covariance matrix as well as the bias correction applied on MWR raw measurements. With the optimal 1D-Var configuration, root-mean-square errors smaller than 1.5 K (respectively 0.8 K) for temperature and 1 g kg⁻¹ (respectively 0.5 g kg⁻¹) for humidity are obtained up to 6 km altitude (respectively within the fog layer up to 250 m). A thin radiative fog case study has shown that the assimilation of MWR observations was able to correct large temperature errors of the AROME (Application of Research to Operations at MEsoscale) model as well as vertical and temporal errors observed in the fog life cycle. A statistical evaluation through the whole period has demonstrated that the largest impact when assimilating MWR observations is obtained on the temperature and LWP fields, while it is neutral to slightly positive for the specific humidity. Most of the temperature improvement is observed during false alarms when the AROME forecasts tend to significantly overestimate the temperature cooling. During missed fog profiles, 1D-Var analyses were found to increase the atmospheric stability within the first 100 m above the surface compared to the initial background profile. Concerning the LWP, the RMSE with respect to MWR statistical regressions is decreased from 101 g m⁻² in the background to 27 g m⁻² in the 1D-Var analysis. These encouraging results led to the deployment of eight MWRs during the international SOFOG3D (SOuth FOGs 3D experiment for fog processes study) experiment conducted by Météo-France.

A RPG-HATPRO ground-based microwave radiometer (MWR) was operated in a deep Alpine valley during the Passy-2015 field campaign. This experiment aims to investigate how stable boundary layers during wintertime conditions drive the accumulation of pollutants. In order to understand the atmospheric processes in the valley, MWRs continuously provide vertical profiles of temperature and humidity at a high time frequency, providing valuable information to follow the evolution of the boundary layer. A one-dimensional variational (1DVAR) retrieval technique has been implemented during the field campaign to optimally combine an MWR and 1 h forecasts from the French convective scale model AROME. Retrievals were compared to radiosonde data launched at least every 3 h during two intensive observation periods (IOPs). An analysis of the AROME forecast errors during the IOPs has shown a large underestimation of the surface cooling during the strongest stable episode. MWR brightness temperatures were monitored against simulations from the radiative transfer model ARTS2 (Atmospheric Radiative Transfer Simulator) and radiosonde launched during the field campaign. Large errors were observed for most transparent channels (i.e., 51–52 GHz) affected by absorption model and calibration uncertainties while a good agreement was found for opaque channels (i.e., 54–58 GHz). Based on this monitoring, a bias correction of raw brightness temperature measurements was applied before the 1DVAR retrievals. 1DVAR retrievals were found to significantly improve the AROME forecasts up to 3 km but mainly below 1 km and to outperform usual statistical regressions above 1 km. With the present implementation, a root-mean-square error (RMSE) of 1 K through all the atmospheric profile was obtained with values within 0.5 K below 500 m in clear-sky conditions. The use of lower elevation angles (up to 5°) in the MWR scanning and the bias correction were found to improve the retrievals below 1000 m. MWR retrievals were found to catch deep near-surface temperature inversions very well. Larger errors were observed in cloudy conditions due to the difficulty of ground-based MWRs to resolve high level inversions that are still challenging. Finally, 1DVAR retrievals were optimized for the analysis of the IOPs by using radiosondes as backgrounds in the 1DVAR algorithm instead of the AROME forecasts. A significant improvement of the retrievals in cloudy conditions and below 1000 m in clear-sky conditions was observed. From this study, we can conclude that MWRs are expected to bring valuable information into numerical weather prediction models up to 3 km in altitude both in clear-sky and cloudy-sky conditions with the maximum improvement found around 500 m. With an accuracy between 0.5 and 1 K in RMSE, our study has also proven that MWRs are capable of resolving deep near-surface temperature inversions observed in complex terrain during highly stable boundary layer conditions.

Ground-based microwave radiometers (MWRs) offer a new capability to provide continuous observations of the atmospheric thermodynamic state in the planetary boundary layer. Thus, they are potential candidates to supplement radiosonde network and satellite data to improve numerical weather prediction (NWP) models through a variational assimilation of their data. However in order to assimilate MWR observations, a fast radiative transfer model is required and such a model is not currently available. This is necessary for going from the model state vector space to the observation space at every observation point. The fast radiative transfer model RTTOV is well accepted in the NWP community, though it was developed to simulate satellite observations only. In this work, the RTTOV code has been modified to allow for simulations of ground-based upward-looking microwave sensors. In addition, the tangent linear, adjoint, and K-modules of RTTOV have been adapted to provide Jacobians (i.e., the sensitivity of observations to the atmospheric thermodynamical state) for ground-based geometry. These modules are necessary for the fast minimization of the cost function in a variational assimilation scheme. The proposed ground-based version of RTTOV, called RTTOV-gb, has been validated against accurate and less time-efficient line-by-line radiative transfer models. In the frequency range commonly used for temperature and humidity profiling (22–60 GHz), root-mean-square brightness temperature differences are smaller than typical MWR uncertainties (∼ 0.5 K) at all channels used in this analysis. Brightness temperatures (TBs) computed with RTTOV-gb from radiosonde profiles have been compared with nearly simultaneous and co-located ground-based MWR observations. Differences between simulated and measured TBs are below 0.5 K for all channels except for the water vapor band, where most of the uncertainty comes from instrumental errors. The Jacobians calculated with the K-module of RTTOV-gb have been compared with those calculated with the brute force technique and those from the line-by-line model ARTS. Jacobians are found to be almost identical, except for liquid water content Jacobians for which a 10 % difference between ARTS and RTTOV-gb at transparent channels around 450 hPa is attributed to differences in liquid water absorption models. Finally, RTTOV-gb has been applied as the forward model operator within a one-dimensional variational (1D-Var) software tool in an Observing System Simulation Experiment (OSSE). For both temperature and humidity profiles, the 1D-Var with RTTOV-gb improves the retrievals with respect to the NWP model in the first few kilometers from the ground.

1D-Var temperature retrievals from microwave radiometer and convective scale model

This article focuses on the simulation and the assimilation of satellite infrared observations in convective‐scale numerical weather prediction (NWP) systems. A radiative transfer model that includes profiles for liquid‐water content, ice‐water content and cloud fraction was used to simulate cloud‐affected radiances as background equivalents. This approach avoids the use of cloud parameters (cloud‐top pressure and effective cloud fraction) deduced from a CO₂ slicing algorithm and the modelling of clouds by single‐layer clouds. The advanced radiative transfer model was evaluated using infrared observations measured by the Infrared Atmospheric Sounding Interferometer (IASI). The observation‐screening procedure that was developed to improve the selection of usable cloudy scenes led to a good agreement between observations and background equivalents. For that purpose, a radiance analysis of collocated Advanced Very High Resolution Radiometer (AVHRR) pixels inside each IASI field of view was used. The goal of this preliminary work is to assess the feasibility of adding the cloud variables (liquid and ice‐water contents) to the state vector of the assimilation system. The approach is illustrated with one‐dimensional variational (1D‐Var) retrievals. The physical consistency of the 1D‐Var adjustments is verified with real observations. Then observing‐system simulation experiments (OSSE) are used to validate the 1D‐Var retrievals.

The Infrared Atmospheric Sounding Interferometer (IASI) provides 8461 channels in the infrared spectrum. In current numerical weather prediction (NWP) models, it is not feasible to assimilate all channels and it is known that the information content between adjacent channels is redundant. This issue has been addressed in NWP centres by employing a channel selection strategy. The goal of this article is to add new channels to the existing IASI operational channel selection, aimed at improving the data assimilation in cloudy conditions and the simultaneous retrieval of cloud microphysical variables, specifically liquid and ice water contents. Cloudy profiles from the French convective-scale model Applications of Research to Operations at MEsoscale (AROME) are used in the study to focus on the retrieval of cloud variables over the Mediterranean region. Three channel selection methodologies were evaluated in this study: a statistical approach based on the degrees of freedom of the signal (DFS), a physical method based on the channel spectral sensitivity to the cloud variables and a random selection. To validate the new selections, an idealized framework is used with observing system simulation experiments (OSSE) in the context of one-dimensional variational retrievals. The current operational IASI selection has already been shown to provide good retrievals of cloud variables. However, all the different channel selections improve the results with small differences in the 1D-Var retrievals. Based on the physical and DFS methods, the final sets of 134 channels sensitive to cloud variables are proposed for future investigation in operational implementation. Additional tests on temperature and water-vapour retrieval results, air-mass dependence and cloud microphysical parametrization have also been conducted.