This research focuses on the impact of smoke exhaust volume and smoke vent layout, which are two crucial factors affecting the smoke control efficiency in tunnels, on the smoke exhaust effect in tunnel fires. Numerical simulation methods are employed to investigate the impact of changing the smoke exhaust volume and the smoke vent number on the smoke exhaust performance in a curved tunnel with a ceiling centralized smoke exhaust system. This research primarily examines the length of the smoke distribution, the smoke temperature under the ceiling, the vertical visibility, and the exhausted smoke mass flow rate. The findings indicate that, in a tunnel with a single-side ceiling centralized smoke exhaust mode, an imbalance in smoke distribution occurs between the upstream and downstream of the fire source. The upstream area experiences a higher amount of smoke, while the downstream area has thinner smoke. Increasing the smoke exhaust volume yielded positive effects on smoke control, as evident in the reduced the smoke spread range, and improved the smoke exhaust efficiency. The influence of changing smoke vent number on the smoke exhaust effect was dependent on the smoke exhaust volume. When the smoke exhaust volume was excessive, altering the number of smoke vents had a minimal impact on smoke exhaust, while in cases with small smoke exhaust volumes, changes in smoke vent numbers obviously influenced the smoke control effect. Therefore, selecting an appropriate smoke exhaust volume and raising the smoke vent number can effectively optimize the performance of the ceiling centralized smoke exhaust system.
This paper built a three‐dimensional layered structure model of semirigid base asphalt pavement with single and double transverse reflective cracks based on the Extended Finite Element Method and fatigue fracture theory. The effects of the number of cracks, crack spacing, and crack length on the stress intensity factors (KI, KII, and Keff) under moving vehicle loads were studied. The fracture life of the asphalt pavement structure was calculated based on the Pairs formula. The results demonstrate that reflective cracks in semirigid asphalt pavement are composite cracks of type I and type II under moving vehicle loads, and shear fracture is the main reason for the failure of the base. The damage to the pavement base will be accelerated with the increase in the number of cracks and the length of the cracks. As the distance between the two reflection fractures is closer, the interaction between the cracks has a superimposed enhancement effect on the crack propagation. Compared with the single nonpenetrating crack model, the fatigue life of the nonpenetrating reflective crack in the double crack pavement structure with a crack spacing of 30 cm is reduced by 46.87%. The research on the propagation mechanism of reflective cracks in this paper provides the essential theoretical and numerical basis for the design, construction, working condition evaluation, and maintenance of pavement structures.
This paper presents a modified time discontinuous Galerkin finite element method (MDGFEM) for transient acoustic wave propagation problem of multilayered pavement. The pavement consists of cement concrete pavement, semi-rigid base, and natural soil. The multilayered pavement is modeled as poroelastic mediums and assumed to be water-saturated. The well-known generalized Biot’s theory is employed to describe the wave propagation problem. The present MDGFEM, based on the artificial damping scheme, employs the Hermite (P3) functions and the linear (P1) shape functions to interpolate the global nodal vector and its temporal gradient respectively in a time step. Numerical results of 1D and 2D problems show that the MDGFEM can filter out spurious numerical oscillations before and after waves, boundaries of the hole, and the interface between the layers more effectively for the propagation of acoustic waves in multilayered pavement. Compared with widely used time-continuous methods such as the Newmark method, the method proposed in this paper presents better capabilities in the fluid–structure interaction behavior of multilayer pavements and provides a more accurate solution, which contributes to the further development of non-destructive testing of multilayer pavement structures.
30 July 2022 in Journal of Vibration Engineering & Technologies
The inclination angle of the spacecraft seat is related to the astronaut’s reentry angle, which in turn affects the safety of the astronauts. This study quantitatively analyzed the effects of different seat inclination angles on astronauts’ lumbar spine injuries using the finite element method during the Lunar-Earth reentry. Firstly, a finite element model of the astronaut’s lumbar spine was constructed based on reverse engineering technology, and the effectiveness of the model was verified through mesh sensitivity, vertebral range of motion, and spinal impact experiments. Then, simulation calculations were carried out for different seat inclination angles (0°, 10°, 20°, and 30°) under the typical reentry return loads of Chang’e 5T1 (CE-5T1) and Apollo 10, and the prediction and evaluation of lumbar spine injuries were conducted in conjunction with the biological tissue injury criteria. The results indicated that the stress on the vertebrae and annulus fibrosus increased under both reentry loads with the rise of the seat inclination angle, but the increasing rates decreased. When the acceleration peak of CE-5T1 approached 9G, the risk of tissue injury was higher under the seat angle exceeded 20°. According to the Multi-Axis Dynamic Response Criteria for spinal injury, neither of the two load conditions would directly cause injury to the astronauts’ lumbar spine when the seat inclination angle was below 30°. The study findings provide a numerical basis for designing and improving the spacecraft’s inclination angle in crewed lunar missions, ensuring the safety of astronauts.