Luoyu R Xu

Prof. Dr. Luoyu R Xu

orcid

Research Focus & Metrics

Academic Career Length

22Years (2005-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2005 in International Journal of Damage Mechanics
Verified
Journal Article
Closed access
PDF file
LXLuoyu R Xu
Luoyu R Xu
ARAres J. Rosakis
Ares J. Rosakis
A systematic experimental investigation of the generation and subsequent evolution of impact damage in heterogeneous two-layer materials is presented. Model layered specimens involving a compliant polymer layer bonded with a metal layer were designed and subjected to impact loading to simulate failure mechanisms in real time. High-speed photography and dynamic photoelasticity were utilized to visualize the nature and sequence of dynamic failure modes. A series of complex failure modes was documented. Interlayer crack growth (interfacial delamination) is the dominant dynamic failure mode. These cracks appear to be shear dominated and might proceed with intersonic speeds. Intralayer cracking always occurs in a local Mode I crack inside the weak layer. Both impact speed and interfacial bonding strength have significant influence on the impact failure. High-impact loading leads to high interlayer crack speeds. Specimens featuring ductile and weak bonds subjected to high-impact speeds are shown to feature intersonic cracks with clearly visible shear shock wave (Mach lines) emitted from the crack tips.

17 November 2014 in The Journal of Adhesion
Verified
Journal Article
Closed access
Kai ZhaoKai Zhao
Kai Zhao
LXLuoyu R Xu
Luoyu R Xu
The relationship between the adhesive bonding strengths and the bonding areas (sizes) is important for material and structural designs, because adhesive bonding is widely used not only in small scale electronic devices, but also in large-scale composite–metal joints of modern aircraft/ship structures. Therefore, a systematic experimental investigation on adhesive bonding strengths of polymer/polymer, metal/metal, and polymer/metal joints was conducted. Results show that the size effect of the bonding strengths is small for the current bonding areas (from 30 to 300 mm2), which are widely employed in most of the test standards for engineering designs.

15 July 2019 in Experimental Mechanics
Verified
Journal Article
Closed access
PDF file
LXLuoyu R Xu
Luoyu R Xu
RMR. Martinez
R. Martinez
KZK. Zhao
K. Zhao

29 May 2024 in Composites Part A: Applied Science and Manufacturing
Verified
Journal Article
Closed access
GZGonghe Zhang
Gonghe Zhang
XZXiaodong Zheng
Xiaodong Zheng
QWQinglin Wang
Qinglin Wang
YNYinxu Ni
Yinxu Ni
FLFenghua Liu
Fenghua Liu
LXLuoyu R Xu
Luoyu R Xu

26 September 2022 in Polymers
Verified
Journal Article
Open access
PDF file
LXLuoyu R Xu
Luoyu R Xu
QWQinglin Wang
Qinglin Wang
YNYinxu Ni
Yinxu Ni
GZGonghe Zhang
Gonghe Zhang
FLFenghua Liu
Fenghua Liu
Yang LiuYang Liu
Yang Liu
Because additively manufactured materials are increasingly being used in load-bearing structures, strength research has become critical. Surprisingly, numerous studies have reported the tensile strength measurements, but only a few studies have presented meaningful results for the shear strength measurements of additively manufactured polymers. Hence, this paper proposes a combined experimental and numerical investigation of a new interlayer shear strength measurement approach, and it targeted the applications of the same polyamide (PA12) specimens made with fused deposition modeling (FDM) and selective laser sintering (SLS). A necking-shaped shear specimen was developed to measure the pure shear strengths with the aid of a three-dimensional (3D) finite element analysis. The results showed that the specimens made with FDM and SLS exhibited totally different shear failure behaviors. The ultimate shear strength of the FDM-PA specimens had more than a 32% increase over that of the SLS-PA specimens. An interface mechanics assumption was employed to explore the different shear failure mechanisms with the support of a fractography analysis.

22 October 2020 in Journal of Composite Materials
Verified
Journal Article
Closed access
PDF file
LXLuoyu R Xu
Luoyu R Xu
MHMd Mehadi Hassan
Md Mehadi Hassan
OAOsman Anderoglu
Osman Anderoglu
KZKai Zhao
Kai Zhao
MFMark Flores
Mark Flores
Previous approaches to measure the through-thickness Young’s modulus of a composite laminate often employed complicated specimens and test procedures, so very few through-thickness Young’s moduli were reported. An efficient spherical nanoindentation approach was developed to measure the through-thickness Young’s moduli of a woven fibric glass-fiber composite laminate. In this paper, the same approach is extended to the modulus measurement of four carbon fiber/epoxy IM7/937-7 laminates with complicated stacking sequences. The measured through-thickness Young’s moduli were consistent with the transverse Young’s modulus of the same composite system. Results show that the stacking sequences have little influence on the through-thickness Young’s moduli, which could be explained by classical lamination theory for a thin composite laminate.