Limiting the consumption of nonrenewable resources and minimizing waste production and associated gas emissions are the main priority of the construction sector to achieve a sustainable future. This study investigates the sustainability performance of newly developed binders known as alkali-activated binders (AABs). These AABs work satisfactorily in creating and enhancing the concept of greenhouse construction in accordance with sustainability standards. These novel binders are founded on the notion of utilizing ashes from mining and quarrying wastes as raw materials for hazardous and radioactive waste treatment. The life cycle assessment, which depicts material life from the extraction of raw materials through the destruction stage of the structure, is one of the most essential sustainability factors. A recent use for AAB has been created, such as the use of hybrid cement, which is made by combining AAB with ordinary Portland cement (OPC). These binders are a successful answer to a green building alternative if the techniques used to make them do not have an unacceptable negative impact on the environment, human health, or resource depletion. The Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) software was employed for choosing the optimal materials’ alternative depending on the available criteria. The results revealed that AAB concrete provided a more ecologically friendly alternative than OPC concrete, higher strength for comparable water/binder ratio, and better performance in terms of embodied energy, resistance to freeze–thaw cycles, high temperature resistance, and mass loss due to acid attack and abrasion.

It is rather costly and difficult to experimentally evaluate the performance of concrete-filled tubular (CFT) circular steel columns exposed to combined axial and cyclic lateral loads. This research paper uses the nonlinear finite element (NLFEA) technique to assess the influence of using carbon-fiber-reinforced polymer (CFRP) laminates on the structural response and failure mode of damaged-by-sulfate CFT circular steel columns. At the beginning, twenty-one CFT circular steel column models were devised and checked for soundness using the findings of previously conducted research. Next, the models were broadened to investigate how the models’ behavior was influenced by the CFRP number of layers and the level of sulfate damage. For experimental purposes, the numbers of CFRP layers were set to be zero, five, six, seven, eight, nine, and ten, while there were three levels of sulfate damage, namely: level 0 (undamaged), level 1 (73 days), and level 2 (123 days). Some of the models were left unconfined with CFRP wraps for comparison. The CFRP confinement was at the end of the models due to its importance regarding the models’ capacity of lateral load. The columns’ ends were confined to prevent the models from outward local buckling, which led to higher strength, bigger net drift, and enhanced energy dissipation. The NLFEA models were then appropriately modified and adjusted in accordance with credible previously conducted experimental research; after which, a parametric study was performed to investigate how the models’ behavior was affected by the number of CFRP layers and the level of axial load. The study found that the CFT circular steel column models’ performance significantly enhanced when the models were wrapped with five to ten CFRP layers. It must be mentioned, though, that using eight, nine, and ten CFRP layers gave almost similar results. In addition, the NLFEA results revealed that when the damaged-by-sulfate models were repaired externally with CFRP wraps, there was an improvement in the models’ cyclic behavior, as they showed a raise in the load capacity, an enhancement in the horizontal displacement, a greater displacement ductility, better energy dissipation, and little deterioration in secant stiffness. The study found that using wraps of CFRP proved a great efficiency with the change in the sulfate damage level.

In concrete production, the use of high-volume fly ash (FA) as the cement substitute became interesting to achieve more sustainable and eco-friendly construction materials. However, concrete produced using high volumes of FA as cement substitute suffers from various limitations such as low strength at early ages. Considering the engineering solutions and economy of FA-included concrete, it has become vital to address such issues. In this perception, some concrete mixes were designed using more abundant and low-cost local waste materials such as waste glass bottle nanopowders (WGBNPs) and effective microorganisms (EMs) to determine the feasibility of compensating for the strength loss at early ages due to FA inclusion. The proposed mixes contained 10% of EMs as water replacement, 50% of FA, and various percentages of WGBNPs as cement replacement. The effects of EMs and WGBNPs inclusion on the early strength and microstructure properties of the produced FA-based concrete mixes were determined. The results show that the strength indexes of the concrete at all test ages were improved due to WGBNP and EM incorporation. At almost all curing ages, the mechanical performance of the concrete made with 10% EMs and 4% WGBNPs was comparable to that of normal concrete (control mix), wherein the mix containing 6% WGBNPs outperformed the control mix. The microstructure analysis of the studied mixes revealed an increase in the hydration products, structural compactness, and homogeneity due to the synergy of WGBNPs and EMs, especially the specimen made using 10% EMs and 6% WGBNPs. It is established that the proper utilization of EMs and WGBNPs in FA-based concrete can be beneficial for waste recycling and landfill problems, thus lowering environment pollution.