A novel material composed of Au@SiO₂-(3-Aminopropyl Triethoxysilane) (Au@SiO₂-APTES) was successfully synthesised using the sol–gel method, and was used to modify glassy carbon electrodes. Its effectiveness as a molecular recognition element is evaluated in the design of an electrochemical sensor for the precise detection of dopamine. The Au@SiO₂-APTES composite was analysed using Fourier transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction. Elemental analysis verified the presence of oxygen, silicon, and gold, with atomic percentages of around 77.19%, 21.12%, and 1.65%, respectively. The corresponding elemental mapping for Au@SiO₂-APTES composite showed that the spatial distribution of all the elements was fairly homogeneous throughout the composite, indicating that the Au NPs are embedded in the silica structures. Traces of dopamine were detected by differential pulse voltammetry with a low limit of detection (S/N = 3) and quantification (S/N = 10) of 1.4 × 10⁻⁸ molL⁻¹ and 4.7 × 10⁻⁸ molL⁻¹, respectively. The Au@SiO₂-APTES composite had two linear ranges: from 4.7 × 10⁻⁸ to 1 × 10⁻⁷ molL⁻¹ and 1.25 × 10⁻⁷ to 8.75 × 10⁻⁷ molL⁻¹. Moreover, the sensor showed outstanding selectivity even in the presence of various potential interfering species. It also demonstrated good reusability and signal recovery when tested in human urine and plasma samples spiked with different dopamine concentrations. The electrochemical sensor, constructed using this novel composite material, shows great promise in the selective and sensitive detection of dopamine in the biological matrix. These results underscore the sensor’s capability for practical application in analysing real-world samples.

Breaking down lignin into smaller units is the key to generate high value‐added products. Nevertheless, dissolving this complex plant polyphenol in an environment‐friendly way is often a challenge. Levulinic acid, which is formed during the hydrothermal processing of lignocellulosic biomass, has been shown to efficiently dissolve lignin. Herein, levulinic acid was evaluated as a medium for the reductive electrochemical depolymerization of the lignin macromolecule. Copper was chosen as the electrocatalyst due to the economic feasibility and low activity towards the hydrogen evolution reaction. After depolymerization, high‐resolution mass spectrometry and nuclear magnetic resonance spectroscopy revealed lignin‐derived monomers and dimers. A predominance of aryl ether and phenolic groups was observed. Depolymerized lignin was further evaluated as an anti‐corrosion coating, revealing enhancements on the electrochemical stability of the metal. Via a simple depolymerization process of biomass waste in a biomass‐based solvent, a straightforward approach to produce high value‐added compounds or tailored biobased materials was demonstrated.

This paper describes the results obtained on the preparation of films composed of linter cellulose and the corresponding acetates. The acetylation was carried out in the LiCl/DMAc solvent system. Films were prepared from a LiCl/DMAc solution of cellulose acetates (degree of substitution, DS 0.8–2.9) mixed with linter cellulose (5, 10 and 15 wt %). Detailed characterization of the films revealed the following: (i) they exhibited fibrous structures on their surfaces. The strong tendency of the linter cellulose chains to aggregate in LiCl/DMAc suggests that these fibrous elements consist of cellulose chains, as can be deduced from SEM images of the film of cellulose proper; (ii) the cellulose acetate films obtained from samples with DS 2.1 and 2.9 exhibited microspheres on the surface, whose formation seems to be favored for acetates with higher DS; (iii) AFM analysis showed that, in general, the presence of cellulose increased both the asperity thickness and the surface roughness of the analyzed films, indicating that cellulose chains are at least partially organized in domains and not molecularly dispersed between acetate chains; and (iv) the films prepared from cellulose and acetates exhibited lower hygroscopicity than the acetate films, also suggesting that the cellulose chains are organized into domains, probably due to strong intermolecular interactions. The linter and sisal acetates (the latter from a prior study), and their respective films, were prepared using the same processes; however, the two sets of films presented more differences (as in humidity absorption, optical, and tensile properties) than similarities (as in some morphological aspects), most likely due to the different properties of the starting materials. Potential applications of the films prepared in tissue engineering scaffold coatings and/or drug delivery are mentioned.

The ability of mimicking the extracellular matrix architecture has gained electrospun scaffolds a prominent space into the tissue engineering field. The high surface-to-volume aspect ratio of nanofibers increases their bioactivity while enhancing the bonding strength with the host tissue. Over the years, numerous polyesters, such as poly(lactic acid) (PLA), have been consolidated as excellent matrices for biomedical applications. However, this class of polymers usually has a high hydrophobic character, which limits cell attachment and proliferation, and therefore decreases biological interactions. In this way, functionalization of polyester-based materials is often performed in order to modify their interfacial free energy and achieve more hydrophilic surfaces. Herein, we report the preparation, characterization, and in vitro assessment of electrospun PLA fibers with low contents (0.1 wt %) of different curcuminoids featuring π-conjugated systems, and a central β-diketone unit, including curcumin itself. We evaluated the potential of these materials for photochemical and biomedical purposes. For this, we investigated their optical properties, water contact angle, and surface features while assessing their in vitro behavior using SH-SY5Y cells. Our results demonstrate the successful generation of homogeneous and defect-free fluorescent fibers, which are noncytotoxic, exhibit enhanced hydrophilicity, and as such greater cell adhesion and proliferation toward neuroblastoma cells. The unexpected tailoring of the scaffolds’ interfacial free energy has been associated with the strong interactions between the PLA hydrophobic sites and the nonpolar groups from curcuminoids, which indicate its role for releasing hydrophilic sites from both parts. This investigation reveals a straightforward approach to produce photoluminescent 3D-scaffolds with enhanced biological properties by using a polymer that is essentially hydrophobic combined with the low contents of photoactive and multifunctional curcuminoids