With the development of the engineering construction industry, knowledge became an important strategic resource for construction enterprises, and knowledge graphs are an effective method for knowledge management. In the context of peak carbon dioxide emissions and carbon neutrality, low carbon emission became one of the important indicators for the selection of construction schemes, and knowledge management research related to low carbon construction must be performed. This study investigated a method of incorporating low-carbon construction knowledge into the bridge construction scheme knowledge graph construction process and proposed a bridge construction scheme recommendation method that considers carbon emission constraints based on the knowledge graph and similarity calculation. First, to solve the problem of the poor fitting effect of model parameters caused by less annotation of the corpus in the bridge construction field, an improved entity recognition model was proposed for low-resource conditions with limited data. A knowledge graph of low carbon construction schemes for bridges was constructed using a small sample dataset. Then, based on the construction of this knowledge graph, the entities and relationships related to construction schemes were obtained, and the comprehensive similarity of bridge construction schemes was calculated by combining the similarity calculation principle to realize the recommendation of bridge construction schemes under different constraints. Experiments on the constructed bridge low carbon construction scheme dataset showed that the proposed model achieved good accuracy with named entity recognition tasks. The comparative analysis with the construction scheme of the project verified the validity of the proposed construction scheme considering carbon emission constraints, which can provide support for the decision of the low-carbon construction scheme of bridges.
This paper proposes an improved calibration method for a structured light system by using the random sample consensus (RANSAC) method with nonlinear optimization and an improved gray centroid method. The proposed method is composed of two steps: calibrating intrinsic and extrinsic parameters for the camera, exploiting the improved gray centroid method to extract the centerline, and fitting the structured light plane by the RANSAC approach with the three-dimensional (3D) points obtained from different positions. The error function caused by the extracted centerline is deduced based on the pixel error perturbation method. The error results of the 3D points are simulated and analyzed. An imaging system is built to realize the 3D imaging. The experimental results show that the calibration error is within 0.08 mm and the reconstruction error is less than 0.45 mm. Moreover, it performs better for the reconstruction of complex objects compared with traditional methods.
5 April 2024 in Nondestructive Testing and Evaluation
TLS can quickly and accurately capture object surface coordinates. However, TLS point clouds cannot cover the entire surface of the target object, due to block of view and limitation of measurement condition. Thus, using it to monitor deformation of slope reduces the detection accuracy of slope surface deformation. To overcome the drawbacks, a method to improve TLS point clouds by UAV photogrammetric point clouds is proposed. The two kinds of point clouds are registered as the new multi-view point clouds by PCA and ICP. The locations of monitoring points are extracted based on HSL color space recognition method from the new multi-view point clouds to analyze the surface displacement. At present, the proposed method has applied in a highway slope in Yunnan Province, and complete point clouds were successfully constructed. A RTK survey was used to compare and verify the proposed method. The verification result demonstrate that the difference of displacement between two measurement methods is less than 10 mm. Comprehensive experiments demonstrate that the proposed method is reliable and meets the slope displacement monitoring standard.
The empirical formula is one of the traditional methods used for predicting ground deformation settlement caused by tunnel excavation. Due to its rationality and simplicity, the Peck formula is widely used for predicting surface subsidence. However, due to its limitations, it is necessary to modify it when predicting surface settlement caused by tunnel excavation in different strata. In this paper, a correction formula for the width coefficient of a tunnel surface settlement slot is derived from the Peck formula by taking into account the theory of strata slip cracks. Values are calculated using the correction formula and compared with measured data to verify the effectiveness of the correction formula. The main conclusions are: (1) The position corresponding to the width of the settlement in the Peck curve is the point where the formation is most prone to slip cracking. (2) In the general shallow buried case, the settlement groove width coefficient K and the internal friction angle φ of the ground satisfy the formula K = 1/tan(45° + φ/2 + a) + b, and the values of parameters a and b reflect the average values of the geometric properties of the tunnel based on the measured data. (3) The prediction of the correction formula is consistent with the measured data, and thus the correction formula can be applied to problems related to the stability of shallow buried tunnels.
1 September 2024 in Journal of Intelligent Construction
Many parameters and complex boundaries are involved in the spatial arrangement of an underground powerhouse in a hydropower station, necessitating referencing many relevant cases and specifications. However, in practical applications, retrieving such cases or specifications is difficult, and there is a lack of knowledge regarding cascading logic among design parameters. To address this issue, this study proposes a novel methodology for constructing a targeted knowledge graph, in this case, a knowledge graph for building information modeling (BIM) for underground powerhouses in hydropower plants. Subsequently, based on this knowledge graph, this study develops a question-and-answer (Q&A) system to facilitate subsequent applications. First, the ontology skeleton of the spatial arrangement design of an underground powerhouse in a hydropower station, that represents the knowledge organization structure of the knowledge graph, is constructed by carefully analyzing the requirements for intelligent modeling of underground powerhouses. A large volume of unstructured data is identified based on the optical character recognition (OCR) technology; the collected data are divided into words to extract correlation knowledge using THU Lexical Analyzer for Chinese (THULAC). Subsequently, the knowledge triad of the spatial arrangement of the underground powerhouse is extracted based on ChatGPT and stored in Neo4j, a knowledge base, to build a knowledge graph. Finally, the knowledge graph is employed to realize the query of knowledge and parameter recommendation to assist the digital intelligent design of the spatial arrangement of an underground powerhouse in a pumped storage hydropower station.
About Me
Jia He, Ph.D., Tianjin University, major direction: hydraulic structure.
Jia He, Ph.D., Tianjin University, major direction: hydraulic structure.