It is recommended to use high-quality thermal insulation materials to increase the energy efficiency of buildings. One of the best thermal insulation materials is foam glassdurable, porous material that is resistant to almost any effect of substance. Glass foaming is a complex process depending on the foaming mode and the initial mixture composition. This paper discusses the influence of all components of the mixture-glass powder, foaming agent, enveloping material and water-on the foam glass structure. It was determined that glass powder is the basis of the future material. A foaming agent forms a gas phase in the process of thermal decomposition. This aforementioned gas foams the viscous glass mass. The unreacted residue thus changes a colour of the material. The enveloping agent slows the foaming agent decomposition preventing its premature burning out and, in addition, helps to accelerate the sintering of glass particles. The introduction of water reduces the viscosity of the foaming mixture making it evenly distributed and also promotes the formation of water gas that additionally foams the glass mass. The optimal composition for producing the foam glass with the density of 150 kg/m 3 is defined according to the results of the research.
The possibility of improving the properties of porous geopolymer materials based on ash and slag waste from thermal power plants by adjusting their chemical composition is considered. An X-ray phase analysis of ash and slag wastes was carried out, the geopolymers’ precursor compositions were calculated, and additives to correct their chemical composition were selected. The samples were synthesized and their physical and mechanical properties (density, porosity, compressive strength, thermal conductivity) were analyzed. The micro- and macro-structure of the samples and the pore distribution of the obtained geopolymers were studied and pore-distribution histograms were obtained. The influence of Si:Al ratio on structural changes was described. The geopolymers’ phase composition was studied, consisting of an amorphous phase and high quartz and mullite. A conclusion about the applicability of this method for obtaining high-quality porous geopolymers was made.
Foamed glass samples based on a glycerol pore-forming mixture at varied temperatures are synthesized. The structure and properties of the samples are investigated. The effect of varying the glycerol...
The regularities of obtaining foamed alkali-activated geopolymer materials based on different wastes of coal power engineering (fly ash, fuel (boiler) slag, ash, and slag mixture) were considered. The phase composition of the studied waste showed the presence of a significant amount of the amorphous phase, as well as a crystalline phase. mostly in the form of high quartz. The microstructure of studied the waste showed that the fly ash consisted of monodisperse hollow aluminosilicate microspheres, the fuel slag was represented by polydisperse irregular particles, and the ash and slag mixture included both of these materials in different ratios. Blowing agents such as aluminum powder, hydrogen peroxide, and sodium hypochlorite were chosen to achieve the porous structure of the geopolymer materials. The calculations of the geopolymer precursor compositions were carried out. Samples were synthesized, and their physical and mechanical properties, such as density, strength, porosity, and thermal conductivity, were analyzed. The micro- and macrostructure of the samples, as well as the pore distribution of the obtained geopolymers were studied. Conclusions were made on the choice of the most-optimal foaming agent and the optimal coal combustion waste suitable for the synthesis of the geopolymer materials.
Ash and slag waste (ASW) from coal combustion creates significant environmental and economic challenges. A promising method of ASW recycling is alkali activation with geopolymer material formation. This study investigates the influence of activating solution components (sodium hydroxide and sodium silicate) on the formation of porous geopolymers using ASW of different origins. The sodium hydroxide content of 0–4 wt.% and the sodium silicate content of 17–25 wt.% were studied. An increase in sodium hydroxide resulted in decreased density, but it adversely affected the strength. An increase in sodium silicate led to a compromised porous structure with relatively high density and compressive strength. An optimal composition, S19N3, comprising 3 wt.% of sodium hydroxide and 19 wt.% of sodium silicate obtained porous geopolymers with uniformly distributed 1.4–2 mm pores and a corresponding density of 335 kg/m3, a compressive strength of 0.55 MPa, a porosity value of 85.6%, and a thermal conductivity value of 0.075 W/(m·K). A mechanism for porous geopolymer formation was developed, including the interaction of alkaline components with ASW and a foaming agent, foaming, curing, and densification. The mechanism was examined using ASW from the Severodvinsk CHPP-1. This study allows for the optimization of geopolymer mixtures with various waste sources and the utilization of waste materials in the construction industry.