(1) Background: The ex vivo porcine ear model is often used for the determination of the dermal penetration efficacy of chemical compounds. This study investigated the influence of the post-slaughter storage time of porcine ears on the dermal penetration efficacy of chemical compounds. (2) Methods: Six different formulations (curcumin and different fluorescent dyes in different vehicles and/or nanocarriers) were tested on ears that were (i) freshly obtained, (ii) stored for 24 or 48 h at 4 °C after slaughter before use and (iii) freshly frozen and defrosted 12 h before use. (3) Results: Results showed that porcine ears undergo post-mortem changes. The changes can be linked to rigor mortis and all other well-described phenomena that occur with carcasses after slaughter. The post-mortem changes modify the skin properties of the ears and affect the penetration efficacy. The onset of rigor mortis causes a decrease in the water-holding capacity of the ears, which leads to reduced penetration of chemical compounds. The water-holding capacity increases once the rigor is released and results in an increased penetration efficacy for chemical compounds. Despite different absolute penetration values, no differences in the ranking of penetration efficacies between the different formulations were observed between the differently aged ears. (4) Conclusions: All different types of ears can be regarded to be suitable for dermal penetration testing of chemical compounds. The transepidermal water loss (TEWL) and/or skin hydration of the ears were not correlated with the ex vivo penetration efficacy because both an impaired skin barrier and rigor mortis cause elevated skin hydration and TEWL values but an opposite penetration efficacy. Other additional values (for example, pH and/or autofluorescence of the skin) should, therefore, be used to select suitable and non-suitable skin areas for ex vivo penetration testing. Finally, data from this study confirmed that smartFilms and nanostructured lipid carriers (NLC) represent superior formulation strategies for efficient dermal and transdermal delivery of curcumin.

Antioxidants are recommended to prevent and treat oxidative stress diseases. Plants are a balanced source of natural antioxidants, but the poor solubility of plant active molecules in aqueous media can be a problem for the formulation of pharmaceutical products. The potential of PlantCrystal technology is known to improve the extraction efficacy and antioxidant capacity (AOC) of different plants. However, it is not yet proved for plant waste. Black tea (BT) infusion is consumed worldwide and thus a huge amount of waste occurs as a result. Therefore, BT waste was recycled into PlantCrystals using small-scale bead milling. Their characteristics were compared with the bulk-materials and tea infusion, including particle size and antioxidant capacity (AOC) in-vitro. Waste PlantCrystals possessed a size of about 280 nm. Their AOC increased with decreasing size according to the DPPH (1,1-diphenyl-2-picrylhydrazyl) and ORAC (oxygen radical absorbance capacity) assays. The AOC of the waste increased about nine-fold upon nanonization, leading to a significantly higher AOC than the bulk-waste and showed no significant difference to the infusion and the used standard according to DPPH assay. Based on the results, it is confirmed that the PlantCrystal technology represents a natural, cost-effective plant-waste recycling method and presents an alternative source of antioxidant phenolic compounds.

PlantCrystals are obtained by milling plant material to sizes < 10 µm. Due to the disruption of the plant cells, active compounds are easily released, rendering the PlantCrystal technology an effective and low-cost process for the production of environmentally friendly plant extracts. The extracts can be used to produce phytomedicines, nutritional supplements or cosmetic products. Previous studies could already demonstrate the use of PlantCrystals to improve the antimicrobial or antifungal activity of different plants. This study investigated whether PlantCrystal technology is suitable to produce plant derived formulations with high antioxidant capacity. The study also aimed to identify the most suitable production methods for this. Methods: Various plant materials and parts of plants, i.e., seeds, leaves and flowers, and different methods were employed for the production. PlantCrystals were characterized regarding size, physical stability and antioxidant capacity (AOC). Results: PlantCrystals with particles < 1 µm were produced from the different plant materials. Both production methods, i.e., high-pressure homogenization, bead milling or the combination of both were suitable to obtain PlantCrystals. Nano milling of the plant material greatly affected their AOC and resulted in formulations with distinctly higher AOC when compared to classical extracts. Conclusions: Rendering plant material into small sized particles is highly effective to obtain plant extracts with high biological efficacy.