In this work, Fe–decorated nitrogen–doped carbon nanospheres are prepared for electrochemical monitoring of acetaminophen. Via a direct pyrolysis of the melamine–formaldehyde resin spheres, the well–distributed Fe–NC spheres were obtained. The as–prepared Fe–NC possesses enhanced catalysis towards the redox of acetaminophen for abundant active sites and high–speed charge transfer. The effect of loading Fe species on the electrochemical sensing of acetaminophen is investigated in detail. The synergistic effect of nitrogen doping along with the above–mentioned properties is taken advantage of in the fabrication of electrochemical sensors for the acetaminophen determination. Based on the calibration plot, the limits of detection (LOD) were calculated to be 0.026 μM with a linear range from 0–100 μM. Additionally satisfactory repeatability, stability, and selectivity are obtained.
Polymer electrolyte membrane fuel cells are considered one of the alternatives to fossil energy sources. The slow kinetics of the oxygen reduction reaction (ORR) at the cathode and the high price of Pt-based catalysts remain one of the key challenges for the commercial viability of proton exchange membrane fuel cells. However, their high cost and susceptibility to poisoning severely limit their use for large-scale commercial applications in fuel cells. Heteroatom-doped porous carbon has attracted extensive attention from scientists due to its advantages such as high specific surface area and the properties conferred by heteroatom doping. On the one hand, we discuss a variety of current methods for the preparation of heteroatom-doped porous carbons, including the template method and the activation method. On the other hand, we discuss the application of heteroatom-doped porous carbon in Pt catalysts, transition metal catalysts and metal-free catalysts. Finally, we also present the pre-existing and challenges of heteroatoms in ORR catalysis, which will drive the development of ORR catalysts.
This paper describes a strategy for preparing free-standing reduced graphene oxide@Si nanoparticles (rGO@Si NPs) composite membranes. Graphene oxide (GO) was reduced and self-assembled synchronously with nanoparticles of silicon (Si NPs) on a metal surface and the composite film was subsequently used in a lithium-ion battery (LIB). This work describes several important novel aspects of the reported technology. Firstly, the composite membrane has a flexible self-supporting structure, allowing it to function as an anode material without requiring binders and current collectors. Secondly, the successful assembly of Si NPs and reduced Graphene oxide (rGO) sheets has enabled the production of the rGO@Si NPs composite film with high controllability and orderliness. Thirdly, the conductive nature of graphene has significantly decreased the resistivity while enhancing the electron transport capacity of the battery anode. Lastly, the robust and flexible structure of the graphene sheet has greatly mitigated the large volume variation in Si NPs during charging or discharging, resulting in the rGO@Si NPs composite film exhibiting excellent energy density and high-power density.
We report here, a strategy to prepare Pt/Pd nanoparticles decorated with Co-N-C materials, where Co-N-C was obtained via pyrolysis of ZIF-67 directly. As-prepared Pt/Pd/Co-N-C catalysts showed excellent ORR performance, offered with a higher limit current density (6.6 mA cm−2) and similar half-wave potential positive (E1/2 = 0.84 V) compared with commercial Pt/C. In addition to an ORR activity, it also exhibits robust durability. The current density of Pt/Pd/Co-N-C decreased by only 9% after adding methanol, and a 10% current density loss was obtained after continuous testing at 36,000 s.
12 October 2018 in Journal of the Electrochemical Society
A novel hydrogen peroxide non-enzymatic sensor was fabricated based on efficiently dispersed hemin on boron/nitrogen-co-doped graphene. Which is prepared by the chemically polymerization of pyrrole on graphene oxide, and the following reducing/doping with dimethylamine borane was then performed. Hemin was anchored homogeneously on the surface of the nanocomposite with high efficient loading amount during this reducing/doping process (3.341 × 10−9mol cm−2). Plenty of efficient electro-active sites and high-speed charge-transfer between hemin and polypyrrole/B, N-co-doped graphene result in high electrocatalytic activity for H2O2 reduction. The hemin/polypyrrole/B, N-co-doped graphene nanocomposite was therefore utilized to fabricate a H2O2 non-enzymatic sensor, which shows a wide linear range of 0.05–900 μM with a detection limit of 23.9 nM. Also, this sensor displays good selectivity and stability.