In this work, Fe–decorated nitrogen–doped carbon nanospheres are prepared for electrochemical monitoring of acetaminophen. Via a direct pyrolysis of the melamine–formaldehyde resin spheres, the well–distributed Fe–NC spheres were obtained. The as–prepared Fe–NC possesses enhanced catalysis towards the redox of acetaminophen for abundant active sites and high–speed charge transfer. The effect of loading Fe species on the electrochemical sensing of acetaminophen is investigated in detail. The synergistic effect of nitrogen doping along with the above–mentioned properties is taken advantage of in the fabrication of electrochemical sensors for the acetaminophen determination. Based on the calibration plot, the limits of detection (LOD) were calculated to be 0.026 μM with a linear range from 0–100 μM. Additionally satisfactory repeatability, stability, and selectivity are obtained.
This paper describes a strategy for preparing free-standing reduced graphene oxide@Si nanoparticles (rGO@Si NPs) composite membranes. Graphene oxide (GO) was reduced and self-assembled synchronously with nanoparticles of silicon (Si NPs) on a metal surface and the composite film was subsequently used in a lithium-ion battery (LIB). This work describes several important novel aspects of the reported technology. Firstly, the composite membrane has a flexible self-supporting structure, allowing it to function as an anode material without requiring binders and current collectors. Secondly, the successful assembly of Si NPs and reduced Graphene oxide (rGO) sheets has enabled the production of the rGO@Si NPs composite film with high controllability and orderliness. Thirdly, the conductive nature of graphene has significantly decreased the resistivity while enhancing the electron transport capacity of the battery anode. Lastly, the robust and flexible structure of the graphene sheet has greatly mitigated the large volume variation in Si NPs during charging or discharging, resulting in the rGO@Si NPs composite film exhibiting excellent energy density and high-power density.
We report here, a strategy to prepare Pt/Pd nanoparticles decorated with Co-N-C materials, where Co-N-C was obtained via pyrolysis of ZIF-67 directly. As-prepared Pt/Pd/Co-N-C catalysts showed excellent ORR performance, offered with a higher limit current density (6.6 mA cm−2) and similar half-wave potential positive (E1/2 = 0.84 V) compared with commercial Pt/C. In addition to an ORR activity, it also exhibits robust durability. The current density of Pt/Pd/Co-N-C decreased by only 9% after adding methanol, and a 10% current density loss was obtained after continuous testing at 36,000 s.
The electrocatalytic carbon dioxide (CO2) reduction reaction (CO2RR) is extensively regarded as a promising strategy to reach carbon neutralization. Copper sulfide (CuS) has been widely studied for its ability to produce C1 products with high selectivity. However, challenges still remain owing to the poor selectivity of formate. Here, a Bi/CeO2/CuS composite was synthesized using a simple solvothermal method. Bi/CeO2–decorated CuS possessed high formate selectivity, with the Faraday efficiency and current density reaching 88% and 17 mA cm−2, respectively, in an H-cell. The Bi/CeO2/CuS structure significantly reduces the energy barrier formed by OCHO*, resulting in the high activity and selectivity of the CO2 conversion to formate. Ce4+ readily undergoes reduction to Ce3+, allowing the formation of a conductive network of Ce4+/Ce3+. This network facilitates electron transfer, stabilizes the Cu+ species, and enhances the adsorption and activation of CO2. Furthermore, sulfur catalyzes the OCHO* transformation to formate. This work describes a highly efficient catalyst for CO2 to formate, which will aid in catalyst design for CO2RR to target products.
Lignin, which contains aromatic phenols, is the second most abundant renewable biomass material in the world. It is the main byproduct of the paper industry and is characterized by abundant sources, renewability, and low cost. The present study focused on the extraction of lignin from poplar wood through a straightforward papermaking approach, thereafter utilizing the resultant black liquor containing lignin for synthesizing lignin-based phenolic resins. During the polymerization process, cobalt (Co) and nickel (Ni) species were introduced and, subsequently, a CoNi/biochar catalyst was obtained through pyrolysis in a nitrogen atmosphere. The prepared catalyst possessed rough spherical structures. The incorporation of Co and Ni enhanced charge redistribution, thereby imparting the catalyst with strong electron acceptance capabilities. The prepared lignin-based phenolic-resin-derived carbon was used for the electrochemical sensing of 2-nitrophenol. The limit of detection (LOD) for 2-nitrophenol was calculated to be 0.0132 µM, with good repeatability, stability, and selectivity.