Long-distance water transmission tunnel projects face significant challenges in crossing active faults. This paper presents a novel multi-layer flexible lining (MFL) structure for high-pressure tunnels that can accommodate fault creep deformation. Finite element numerical analysis was utilized to validate the feasibility of the MFL structure under the actual conditions of a particular engineering project. Additionally, the effects of various parameters on the tunnel structure were examined. The results indicated that shorter concrete segments and longer flexible joints are better able to accommodate fault dislocations and reduce concrete damage. A thicker cushion layer, with a thickness ranging from 0.1 to 0.4 m, is more advantageous for the tunnel lining to adapt to fault dislocations. However, an excessively thick cushion layer will have a negative impact on the lining’s stress. Appropriate use of bellows joints can improve the tunnel resistance to fault displacement. The number of bellows joints needed for effectiveness and the potential failure of the joints at the edge of the fault zone were examined. The research findings can provide valuable guidance for the structural design of high-pressure water transmission tunnels in dealing with fault creep deformation.
Massive reinforced concrete (MRC) structures are utilized in a variety of applications where both mechanical and thermal properties are of concern. A 1:2 large-scale test model of the steel-lined reinforced concrete penstock (a kind of MRC) and a coupled thermomechanical numerical analysis are both implemented to investigate the thermomechanical effects on structural behavior. Three different temperature fields and eight temperature gradients are selected to explore how the temperature affects the crack width, steel stress, and deformation. The results show that the numerical simulation results are consistent with the experimental results and that this method can be applied to other similar MRC structure analysis. The thermal effect can cause 10−3~10−2 mm thermal crack width and ±45 MPa thermal stress and this may lead the total crack width to exceed the limited value and the reinforcement stress beyond the yield strength. Consequently, the influence of the thermomechanical loads cannot be ignored and the corresponding temperature control measures must be taken to ensure structural safety and durability.
The bond–slip behavior of the steel–concrete interface is critical in reinforced concrete (RC) structures since the bond action is the mechanism that ensures the two materials work in co-operation. However, there is little research considering the bond–slip behavior in massive ring-type reinforced concrete (MRRC) structure bearing analyses due to the complexity of modeling the interfacial behavior. Hence, the influence of the bond–slip behavior on the bearing characteristics of MRRC structures remains unclear. Steel-lined reinforced concrete penstock is such an MRRC structure, composed of steel liner and reinforced concrete and commonly used in diversion pipelines. This paper aims to explore the bearing characteristics considering the bond–slip behavior in the composite penstock by using a promising numerical method, the cohesive zone model. Three interface models were proposed to represent the different interaction conditions at the steel–concrete interface. Moreover, a sensitivity analysis was performed to study the impact of the bond strength on the bond performance and structural behavior. The simulation results showed that the prediction results (steel stress and crack process) considering the bond–slip behavior were in good agreement with the experimental results. The steel stresses near the cracks were smaller and more uniform after considering the bond–slip behavior, since the stresses were no longer concentrated on the crack but distributed in an area near the crack. However, the steel stress differences in these models were within 10%, which means that the bond performance had a limited effect on the structural safety design. The crack widths were greatly influenced by the bond conditions, and the maximum crack width (0.461 mm) in poor conditions was beyond the limiting value (0.3 mm). Consequently, bond–slip behavior must be paid more attention in durability design.
By an exposed steel penstock crossing an active fault in high earthquake-intensity areas, the adaptability to fault slip and seismic behavior of the penstock is analyzed by the finite element method in this paper. The results show that it is effective to set several bellow-type expansion joints and arrange sliding and hinge supports at intervals for penstocks crossing active faults to adapt to fault slip. Most of the mass is concentrated on penstock, and each penstock section has a larger stiffness when there are bellow-type expansion joints at the two ends of the penstock section, so the penstock moved nearly rigidly under an earthquake and the stress is caused by internal water pressure mainly. However, as a result of the expansion joints, the axial displacement of the penstock is large and the supporting rings of hinge support bend seriously. Thus it is supposed to avoid excessive expansion joints to improve the axial seismic capacity. In addition, the sliding supports can work as base isolation supports, and excessive horizontal displacement can be restricted by hinge supports, and therefore it is of advantage not only to adaptability to inhomogeneous ground displacement but also to structural seismic behavior to arrange sliding supports and hinge supports at intervals. At the same time, the supports should have enough joint strength, and it is necessary to set restraining devices to avoid the penstock sliding off the supports.