Large-diameter buried steel pipes (BSPs) have been widely utilized in water diversion and hydropower fields. This paper presents a comprehensive numerical investigation on the interaction between the large-diameter pipe and soil under three typical working conditions, to capture the structural mechanical behaviors of pipe deformation, soil displacement, and soil pressure. Furthermore, a parametric analysis of pipe diameter is conducted, along with the sensitivity study of soil parameters based on the orthogonal test method. The results show that the water weight increases the pipe deformation significantly by 14%, while the high internal water pressure decreases the deformation greatly with the maximum effect of 39%. The pattern of soil pressure at the top of the pipe changes from parabola to double-hump as the pipe diameter varies from 0.5 m to 5.0 m. The pipe deformation and soil pressure keep increasing with the pipe diameter, but the safety margin for prism load decreases gradually. Pipe deformation and soil pressure are very sensitive to the elastic modulus and Poisson’s ratio of backfill. Friction coefficients of soil-soil (trench sidewall) and pipe-soil have great influences on the soil pressure, while the bedding material and backfill cohesion have small effects on it.
Under the circumstances of rapid expansion of diverse forms of volatile and intermittent renewable energy sources, hydropower stations have become increasingly indispensable for improving the quality of energy conversion processes. As a consequence, Francis turbines, one of the most popular options, need to operate under off-design conditions, particularly for partial load operation. In this paper, a prototype Francis turbine was used to investigate the pressure fluctuations and hydraulic axial thrust pulsation under four partial load conditions. The analyses of pressure fluctuations in the vaneless space, runner, and draft tube are discussed in detail. The observed precession frequency of the vortex rope is 0.24 times that of the runner rotational frequency, which is able to travel upstream (from the draft tube to the vaneless space). Frequencies of both 24.0 and 15.0 times that of the runner rotational frequency are detected in the recording points of the runner surface, while the main dominant frequency recorded in the vaneless zone is 15.0 times that of the runner rotational frequency. Apart from unsteady pressure fluctuations, the pulsating property of hydraulic axial thrust is discussed in depth. In conclusion, the pulsation of hydraulic axial thrust is derived from the pressure fluctuations of the runner surface and is more complicated than the pressure fluctuations.
Massive reinforced concrete (MRC) structures are utilized in a variety of applications where both mechanical and thermal properties are of concern. A 1:2 large-scale test model of the steel-lined reinforced concrete penstock (a kind of MRC) and a coupled thermomechanical numerical analysis are both implemented to investigate the thermomechanical effects on structural behavior. Three different temperature fields and eight temperature gradients are selected to explore how the temperature affects the crack width, steel stress, and deformation. The results show that the numerical simulation results are consistent with the experimental results and that this method can be applied to other similar MRC structure analysis. The thermal effect can cause 10−3~10−2 mm thermal crack width and ±45 MPa thermal stress and this may lead the total crack width to exceed the limited value and the reinforcement stress beyond the yield strength. Consequently, the influence of the thermomechanical loads cannot be ignored and the corresponding temperature control measures must be taken to ensure structural safety and durability.
The bond–slip behavior of the steel–concrete interface is critical in reinforced concrete (RC) structures since the bond action is the mechanism that ensures the two materials work in co-operation. However, there is little research considering the bond–slip behavior in massive ring-type reinforced concrete (MRRC) structure bearing analyses due to the complexity of modeling the interfacial behavior. Hence, the influence of the bond–slip behavior on the bearing characteristics of MRRC structures remains unclear. Steel-lined reinforced concrete penstock is such an MRRC structure, composed of steel liner and reinforced concrete and commonly used in diversion pipelines. This paper aims to explore the bearing characteristics considering the bond–slip behavior in the composite penstock by using a promising numerical method, the cohesive zone model. Three interface models were proposed to represent the different interaction conditions at the steel–concrete interface. Moreover, a sensitivity analysis was performed to study the impact of the bond strength on the bond performance and structural behavior. The simulation results showed that the prediction results (steel stress and crack process) considering the bond–slip behavior were in good agreement with the experimental results. The steel stresses near the cracks were smaller and more uniform after considering the bond–slip behavior, since the stresses were no longer concentrated on the crack but distributed in an area near the crack. However, the steel stress differences in these models were within 10%, which means that the bond performance had a limited effect on the structural safety design. The crack widths were greatly influenced by the bond conditions, and the maximum crack width (0.461 mm) in poor conditions was beyond the limiting value (0.3 mm). Consequently, bond–slip behavior must be paid more attention in durability design.
1 December 2021 in KSCE Journal of Civil Engineering
Large-diameter buried steel pipes (BSPs) play critical roles in water transport for major water diversion and hydropower projects. Due to poor pipe-soil composite system properties and installation conditions, they are prone to excessive deformation, resulting in safety hazards. This paper takes a BSP project subjected to excessive deformation as an example. A simplified numerical model is first established to analyze the structural performance, including the stress and plasticity, and the relationship between the stress and deformation of the pipe. Furthermore, a jacking method to rehabilitate the pipe-soil composite system is conducted to explore its influences on pipe deformation, stress, and plasticity. The results show that considerable bending stresses occur in the pipe and that sections of the midspan and stiffening ring are in the pure bending state and eccentric bending state, respectively. Areas of high stress and plasticity center at the crown, springline, and invert of the pipe, and steel pipes with ring deformation of 8.9% can be continued to be used, as the full yielding of the pipe walls occurs at the ring deformation of 15.8%. The jacking method is an effective solution for the rehabilitation of BSPs subjected to large deformation and can reduce pipe deformation significantly while increasing the stress at the pipe crown and the pipe plasticity only slightly.