This article proposes an active-matrix organic light-emitting diode (AMOLED) pixel circuit for mobile displays with high resolution to improve the image quality of the display panel. The proposed pixel circuit, which consists of six low-temperature polycrystalline silicon thin-film transistors (TFTs) and two capacitors, compensates for variations in the threshold voltage (Vth) and subthreshold slope (SS) of driving TFTs at low gray levels. Such compensations are achieved by extending the compensation time in the diode-connection scheme, resulting in a reduction in the OLED current error (OCE) of the proposed pixel circuit. In addition, the proposed pixel circuit connects two capacitors in parallel to the gate node of the driving TFT, thus increasing the total storage capacitance value in a given capacitor area in the emission phase, resulting in a reduction in voltage distortion at the gate node. Moreover, the OCEs caused by the IR drop of ELVDD and the crosstalk due to parasitic capacitances are thoroughly investigated and analyzed. The measurement results of the proposed pixel circuit show that the OCEs at the 64th and 128th gray levels are reduced from ±3.5 and ±6.5 to ±2.0 and ±0.8 LSB, respectively, by extending the compensation time from 6.5 to 195 μs. Therefore, the proposed pixel circuit is highly suitable for mobile AMOLED displays requiring high image quality.
16 August 2019 in IEEE Journal of the Electron Devices Society
This paper proposes a pixel circuit with high resolution and high luminance uniformity for organic light emitting diode-on-silicon (OLEDoS) microdisplays. The proposed pixel circuit employs a simple structure that consists of four n-channel MOSFETs and one capacitor, resulting in high resolution. In addition, this circuit compensates for the threshold voltage (Vth) variation of the driving transistor caused by the body effect, which increases the Vth as the source-to-body voltage of the driving transistor increases, thus reducing the emission current deviation, resulting in a high luminance uniformity. Moreover, the proposed pixel circuit extends the data voltage range using the capacitive coupling of the storage capacitance and the parasitic capacitance at the gate node of the driving transistor to precisely control the emission current. To verify the performance of the proposed pixel circuit, a test pattern with an array of the proposed 4T1C pixel circuits was fabricated on a single-crystalline silicon wafer as a backplane using a 110 nm standard CMOS process with 5.5 V high-voltage devices. The proposed pixel circuit occupies a unit sub-pixel area of 5.76 μm × 1.92 μm, which corresponds to a resolution of 4410 pixels per inch. The measurement results show that the emission current deviation error of the proposed pixel circuit ranges between –1.16% and +1.14%, which is improved from between –45.97% to +45.42% achieved in the conventional current-source type 2T1C pixel circuit, which does not compensate for the Vth variation of the driving transistor. Moreover, the measured data voltage range of the proposed pixel circuit is extended to 1.618 V, which is 8.17 times wider than that of the conventional pixel circuit. Therefore, the proposed pixel circuit is very suitable for high resolution and high luminance uniformity of OLEDoS microdisplays.
15 December 2017 in IEEE Transactions on Power Electronics
This paper presents an average current control method for a light-emitting diode (LED) lamp driver that achieves a highly accurate current and removes low-frequency light flicker. The proposed LED lamp driver accurately maintains an average LED forward current by precisely adjusting the duration of the on- and off-times of the LED lamp driver. It also removes the low-frequency flicker by regulating the LED forward current without being affected by the low-frequency component of the AC line voltage. In addition, it reduces power consumption by eliminating the necessity of a high-voltage sensor or a high-side resistor, which causes conduction loss. The proposed average current controller was fabricated using a 0.18 μm bipolar-CMOS-DMOS process technology. The measurement results of the proposed LED lamp driver show that the variation in the average LED forward current is less than 0.6%, and the light flicker below 120 Hz is completely removed. In addition, the measured maximum power efficiency and power factor of the proposed LED lamp driver are 89.22% and 0.93, respectively.
26 April 2018 in IEEE Transactions on Power Electronics
This letter proposes a fast and highly-accurate battery charger for mobile applications. The proposed battery charger accurately detects the built-in resistance (BIR) and determines the transition point from the constant current (CC) to constant voltage (CV) modes. It then maximizes and minimizes the durations of the CC and CV modes, respectively, thus reducing the battery charging time. In addition, the proposed charger accurately controls the charging current (IBAT) by employing an adaptive off-time-controlled switching charger. The proposed battery charger was fabricated using a 0.18-μm standard CMOS process. The measurement results showed that with the use of the accurate BIR detection and adaptive off-time-control methods, the proposed charger reduced the total charging time by up to 41.2%, and achieved IBAT ripple of 52 mAp-p.
2 February 2017 in IEEE Transactions on Consumer Electronics
In this paper, a polar coordinate-based touch data extraction (PCTDE) algorithm is proposed to enhance the linearity and accuracy of touch coordinates for large-sized capacitive touch screen panels (TSPs) with a wide electrode pitch. The proposed PCTDE algorithm accurately extracts the touch coordinates by calculating the distance and directional angle between the touch point and the intersection of the transmitter and receiver electrodes. In addition, the interference between two touch points in multi-touch is reduced by decreasing the differential rate of touch data so that the exact touch coordinates can be determined. We evaluated the proposed algorithm using a 46-inch TSP with an 8.5 mm electrode pitch. To verify the linearity and accuracy of touch coordinates, the standard deviation of the slope of the touch coordinates and the average distance error are calculated, respectively. In single-touch, the linearity and accuracy of touch coordinates are improved by 56.7 % and 57.8 %, respectively, compared with those using the best previously-reported touch-sensing algorithm. In multi-touch, the linearity and accuracy of touch coordinates are improved by 56.7 % and 64.2 %, respectively.
20 November 2013 in IEEE Transactions on Electron Devices
We investigated the characteristic variation of an integrated thin-film resistor (TFR), which is composed of silicon chromium (SiCr), according to process conditions and its effects on analog circuits. To improve TFR properties, such as temperature coefficient of resistance (TCR) and mismatch, the integrated TFR was examined under various process conditions. First, the sputtering power and the annealing temperature were optimized to control the TCR property. Secondly, the etching time and the dummy pattern were optimized to enhance the mismatch property. The measured TCR is -3.9 ppm/°C and the calculated mismatch slope from the standard deviation of resistance mismatch is 0.34%·μm. These results show that the fabricated TFR had near-zero TCR and a high matching constant. To verify the TFRs effects on analog circuits, low-pass filters (LPFs) were fabricated and measured as a test vehicle; the use of the optimized resistor considerably improved the performance of the resulting LPFs.