In this paper, a method of realizing voltage-mode (VM) non-inverting high-pass filter (HPF), band-pass filter (BPF), low-pass filter (LPF), and inverting low-pass filter (ILPF) transfer functions structure with two grounded capacitors and four resistors through an analytical synthesis method is presented. The synthesis structure of the VM biquadratic filter consists of a voltage proportional block and two voltage lossless integrators based on the use of current feedback operational amplifiers (CFOAs). It is demonstrated that the derived biquadratic filter structure can simultaneously realize VM HPF, BPF and ILPF transfer functions or VM BPF and LPF transfer functions at a high-input impedance terminal. The VM biquadratic filter can independently adjust the resonance angular frequency and quality factor. By slightly modifying the proposed biquadratic filter, a VM quadrature sinusoidal oscillator can be achieved. The proposed biquadratic filter and quadrature oscillator have been simulated by OrCAD PSpice and appropriate hardware has been implemented with AD844-type CFOAs. In order to reduce power consumption, reduce chip area, reduce costs, and improve system integration, integrated VM CFOA-based biquadratic filter circuits and quadrature oscillator circuits are very important. The proposed filter and quadrature oscillator have been further fabricated in 0.18 μm 1P6M CMOS process technology. The entire chip area is 0.974 mm2, including a filter chip cell and an oscillator chip cell. Under the supply voltage of ±0.9 V, the total power dissipation of the filter chip cell is 5.4 mW, and the figure-of-merit (FOM) of filter chip cell is 66.7%. The measured value of the third-order intermodulation distortion of the filter chip cell is -55.29 dBc and the third-order intercept point is 19.9 dBm. The measured phase noise of CFOA-based filter chip cell at 1 kHz offset is less than -99.76 dBc/Hz.
This article presents a versatile voltage-mode (VM) biquad filter with independently electronic tunability. The proposed structure using one dual-output operational transconductance amplifier, three single-output operational transconductance amplifiers (OTAs) and two grounded capacitors was explored to derive a new VM quadrature oscillator with the independent control of the oscillation frequency and the oscillation condition. The proposed versatile VM biquad filter achieves nearly all of the main advantages: (i) simultaneous realizations of band-reject, band-pass, and low-pass from the same architecture, (ii) multiple-input and multiple-output functions, (iii) independent electronic adjustability of quality factor and resonant angular frequency, (iv) no resistor needed, (v) all input terminals with cascade functions, (vi) no additional inverting amplifier for input signals, (vii) using only grounded capacitors, and (viii) easy to implement a VM quadrature oscillator with independent electronically controlled oscillation frequency and oscillation condition. The proposed versatile VM biquad filter employs only four OTAs and two grounded capacitors. The active components of the proposed VM biquad filter are one less than that of recent reports. The proposed circuit also brings versatility and simplicity to the design of VM biquad filters and VM quadrature oscillators. Filters and oscillators with less active and passive components have the advantages of low cost, low power dissipation, low circuit complexity, and low noise. Commercially available integrated circuit LT1228 and discrete components can be used to implement the proposed OTA-based circuits. The simulation and experiment results validated the theoretical analysis.
2 September 2020 in IEEE Transactions on Industrial Electronics
This article presents an improved optimum damping current-mode buck converter with fast-transient response and small-transient voltage using new current sensing circuits. The improved optimum-damping circuit, consisting of the dynamic slope generator and the proposed rail-to-rail current sensor, can stabilize the converter during the output current change and can accelerate the transient response to achieve better figure of merit performance. The dynamic slope generator can compensate the slope to prevent subharmonic oscillation issue and lower undershoot/overshoot without an extra slope compensator. The proposed rail-to-rail current sensor increases the input voltage range, accurately captures the inductor current information, and accelerates the transient response as the load current changes, because it eliminates spikes without the need for a sample-and-hold circuit in a conventional current-sensing circuit. The contributions of the proposed converter are listed in the following: 1) we have proposed a new current-sensing circuit without voltage divider, which can be operated rail-to-rail and improve the dynamic response; 2) the new current-sensing circuit consisted of no switches and therefore, without switching noises; 3) the new current-sensing circuit without voltage divider has a smaller chip area and a smaller path delay; 4) the proposed current-sensing circuit needs no sample-and-hold circuits to reduce current spikes; 5) the transient response and transient voltage of the proposed converter are better than others' works; and 6) we have designed and implemented a new optimum-damping current-mode buck converter with better performances compared with previous publications.
This paper proposes a new high-input impedance current feedback operational amplifier (CFOA)- based voltage-mode multifunction biquadratic filter and a voltage-mode quadrature oscillator using the proposed high-input impedance CFOA-based biquadratic filter. The proposed high-input impedance CFOA-based voltage-mode multifunction biquadratic filter uses three CFOAs, three resistors, and two grounded capacitors with two inputs and three outputs. The filter can simultaneously realize non-inverting low-pass, non-inverting band-pass, and non-inverting band-reject filtering functions at the high-input impedance terminal while the inverting band-pass and non-inverting high-pass filtering functions can also be obtained by applying another high-input impedance terminal. The filter offers orthogonal control of resonance angular frequency and quality factor. The proposed high-input impedance CFOA-based voltage-mode multifunction biquadratic filter can be used to implement a voltage-mode quadrature oscillator with an independently controlled the frequency of oscillator and the condition of oscillation. The OrCAD PSpice simulation and experimental results of the commercially available integrated circuit, AD844AN, are used to confirm the characteristics of the proposed filter and oscillator.
This paper presents the realization of a resistorless third-order quadrature oscillator using two multiple-output current controlled current conveyor transconductance amplifiers (MO-CCCCTAs) and three grounded capacitors. The proposed circuit provides two quadrature voltage outputs, two high-impedance quadrature current outputs, and one high-impedance amplitude-controllable current output. The proposed oscillator satisfies the industrial requirement for amplifier and modulation signals and phase shift keying signals, when the input bias current of the second MO-CCCCTA is used as a modulating signal. Its oscillation condition and oscillation frequency can be adjusted independently by two different bias currents of MO-CCCCTAs. The structure of resistorless and only grounded capacitors suggests that the proposed oscillator can be easily implemented in an integrated circuit.