During the Archaean, the Sun's luminosity was 18 to 25% lower than the present day. One-dimensional radiative convective models (RCM) generally infer that high concentrations of greenhouse gases (CO2, CH4) are required to prevent the early Earth's surface temperature from dropping below the freezing point of liquid water and satisfying the faint young Sun paradox (FYSP, an Earth temperature at least as warm as today). Using a one-dimensional (1-D) model, it was proposed in 2010 that the association of a reduced albedo and less reflective clouds may have been responsible for the maintenance of a warm climate during the Archaean without requiring high concentrations of atmospheric CO2 (pCO2). More recently, 3-D climate simulations have been performed using atmospheric general circulation models (AGCM) and Earth system models of intermediate complexity (EMIC). These studies were able to solve the FYSP through a large range of carbon dioxide concentrations, from 0.6 bar with an EMIC to several millibars with AGCMs. To better understand this wide range in pCO2, we investigated the early Earth climate using an atmospheric GCM coupled to a slab ocean. Our simulations include the ice-albedo feedback and specific Archaean climatic factors such as a faster Earth rotation rate, high atmospheric concentrations of CO2 and/or CH4, a reduced continental surface, a saltier ocean, and different cloudiness. We estimated full glaciation thresholds for the early Archaean and quantified positive radiative forcing required to solve the FYSP. We also demonstrated why RCM and EMIC tend to overestimate greenhouse gas concentrations required to avoid full glaciations or solve the FYSP. Carbon cycle–climate interplays and conditions for sustaining pCO2 will be discussed in a companion paper.
23 March 2022 in Earth and Planetary Science Letters
Scandium (Sc) is used in several modern industrial applications. Recently, significant Sc concentrations (~100 ppm) were reported in some nickel-cobalt lateritic ores, where Sc may be valuably co-produced. However, Sc is typically not included in routine analyses of Ni-Co ores. This contribution examines the relevance of using routinely analysed elements as geochemical proxies for estimating Sc concentration and distribution. Three Ni-Co lateritic deposits from New Caledonia were investigated. In each deposit, Sc is well correlated with Al2O3. The slopes of deposit-scale Sc-Al2O3 regression lines are remarkably controlled by the composition of enstatite from the parent peridotite. In all deposits, maximum Sc enrichment occurs in the yellow limonite, above the highest Ni and Co enrichment zones. Sc- and Al-bearing crystalline goethite is predominant in the oxide-rich zones, though Sc shows a higher affinity for amorphous iron oxides than Al. We propose that, in already assayed Ni-Co lateritic ores, the concentration and distribution of Sc can be estimated from that of Al. Deposit-scale Sc-Al2O3 correlations may be determined after analysing a limited number of spatially and chemically representative samples. Therefore, mining operators may get a first-order evaluation of the Sc potential resource in Ni-Co lateritic deposits at low additional costs.
1 March 2022 in Journal of South American Earth Sciences
Since the development of portable X-ray fluorescence (pXRF) spectrometers, few studies have been conducted on the influence of spectral interferences between chemical elements. This study aims to improve the management of these interferences to obtain more reliable geochemical analyses. We specifically investigate Ca-related interferences on Sc analysis for the case of Ni-rich laterite samples using the Niton XL3t GOLDD + pXRF analyser. Three quantification methods were tested on 59 pelletized samples using the ‘Soil’ mode. The first, named ‘Manufacturer’, represents the elemental quantification directly provided by the device based on regions of interest and multilinear corrections of spectral interferences configured during the spectrometer design. The second, the ‘20 Cu’ method, is based on spectral fitting using the PyMCA software. The third, the ‘18 Fe’ method, combines spectral fitting with modified experimental conditions. For each, a quantification methodology was developed, establishing (i) Ca and Sc calibration lines and (ii) Ca/Sc threshold values delimiting fields of ‘reliable’, ‘to be confirmed’ and ‘unreliable’ measurements. The ‘20 Cu’ and ‘18 Fe’ methods greatly extend the ‘reliable measurements’ field concerning the Ca/Sc ratio compared to the ‘Manufacturer’ method. The ‘18 Fe’ method was also found to provide the most negligible measurement dispersion. Supplementary material: Figures A–F and Tables A and B are available at https://doi.org/10.6084/m9.figshare.c.5511838