Compared with traditional rigid grippers, soft grippers are made of lightweight and soft materials and have the characteristics of flexible contact and strong adaptability, which are widely utilized to grasp fragile objects with complex contours and shapes. In this article, we design and fabricate a three-fingered stiffness-tunable soft gripper by integrating the joint-tuning capability. The soft fingers are composed of an internal bending actuator and an external fiber-jamming jacket, under an actuation of pneumatic pressure. Static and kinematic models are established to detect the bending angle and end trajectory of the internal bending actuator. Meanwhile, the bending angle and blocking force of bending actuator are experimentally measured and are comparably analyzed with the theoretical predictions. Jamming pressure is applied in the stiffness-tunable jacket to explore the variable stiffness and load-carrying capability of the soft finger. By incorporating the stiffness-tunable property, the grasping performance of various weights and types of goods, as well as the maximum grasping force of the soft gripper, is investigated. Finally, by patterning the stiffness-tunable jacket on the bending actuator, the variable curvature bending deformation and joint-tuning capability of the soft finger are achieved. This proposed soft gripper holds great potential applications in soft robotics community.
31 December 2010 in Robotics and Computer-Integrated Manufacturing
Suction cups of cephalopods show a preeminent performance when absorbing irregular or flat objects. In this paper, an octopi-inspired suction cup, driven by hydraulically coupled dielectric elastomer actuators (HCDEAs), is proposed, which is considered to be controlled easily and have compact structure. To investigate the performance of suction cups, experiments have been conducted to clarify the effect of the pre-stretch ratio and chamber angle on suction forces. It could be seen that both factors have a complicated influence on suction forces, and the best performance obtained was a reasonable combination of the pre-stretch ratio and chamber angle. Here, we achieved a maximum suction force of 175 mN with λp = 1.2, α = 23° under a DC voltage of 3500 V. To enhance the capacity and adaptation of the suction cup, flat objects of various types of materials were introduced as targets. Experimental results displayed that for tested materials, including a dry/wet acrylic plate, CD, ceramic wafer, and aluminum plate, the suction cup showed outstanding performance of absorbing and lifting the target without any damage or scratch to them. Our research may serve as a guide to the optimal design and provide insights into the performance of the HCDEAs-actuated suction cup.
In recent years, flexible continuum robots have been substantially developed. Absolute nodal coordinates formulation (ANCF) gives a feasible path for simulating the behavior of flexible robots. However, the model of finger-shaped robots is often regarded as a cylinder and characterized by a beam element. Obviously, this is short of characterizing the geometrical feature of fingers in detail, especially under bending conditions. Additionally, for the lower-order plate element, it is hard to characterize the bending behavior of the flexible finger due to fewer nodes; a higher-order plate element often requires an extremely long computing time. In this work, an improved ANCF lower-order plate element is used to increase the accuracy of the Yeoh model and characterize the geometrical structure of silicone rubber fingers, taking into particular consideration the effect of volume locks and multi-body system constraints. Since it is a kind of lower-order plate element, essentially, the computing time is nearly the same as that of conventional lower-order plate elements. The validity of this model was verified by comparing it with the results of the published reference. The flexible finger, manufactured using silicone rubber, is characterized by the novel ANCF lower-order plate element, whereby its mechanical deformation and bending behavior are simulated both efficiently and accurately. Compared to the ANCF beam element, conventional lower-order plate element, and higher-order plate element, the novel plate element in this paper characterizes the external contour of the finger better, reflects bending behavior more realistically, and converges in less computing time.
The adhesion force generated by electrostatic pads is highly sensitive to fluctuations in environmental temperature and humidity in engineering applications. It may compromise their stability and reliability in complex operating environments. Based on dielectric and solid-state physics, theoretical models were developed to describe the influence of temperature and humidity on the dielectric constant and conductivity of the interfacial medium. An environmental testing platform was then established to systematically evaluate the electroadhesive performance of an electrostatic device composed of a bakelite substrate and an epoxy resin dielectric layer under controlled temperature and humidity conditions. The electrostatic adhesion force increases with the rise in temperature and significantly decreases with the increase in humidity. At 25 °C, the adhesion force significantly decreased within the range of 75% RH to 85%RH. At 38 °C, the humidity causes a significant decrease in the electrostatic adhesion force within the range of 45%–55%RH. At the highest humidity levels, the electrostatic adhesion force was strongly suppressed for each temperature. The findings offer practical guidance for humidity regulation, thermal management and the reliable deployment of electroadhesive technologies in variable engineering environments.