FeFETs with 5-nm-thick Hf0.5Zr0.5O2 (HZO) have been demonstrated in memory operations for the ON/OFF current ratio >104 at zero gate voltage and an MW (memory window) of 0.6-0.7 V. A gradual transition of the ferroelectricity with an increasing crystallization temperature for the gate-last process was presented. The excellent program/erase (P/E) data retention are the ~2x104 ON/OFF ratio and 0.67 V extrapolated to 10 years with VP/E=±b4.8 V. The MW remains >0.2 V after 106 cycles for read and vanishes with cycles of 103-104 for write, which is the bottleneck for ferroelectric-type memories. The mechanism of retention and endurance are discussed. The characteristic of this work is an unaffected coercive-field (~1 MV/cm) with scaling FE-HZO down to 5-nm-thick, which is beneficial for reducing the operation voltage. Comparable performance with previous works on high data retention and endurance with low voltage for read are achieved. The ultrathin ferroelectric layer proposes a realistic emerging memory for 1T architecture.
31 August 2020 in IEEE Transactions on Electron Devices
Atomic layer deposition (ALD)-based TiN electrode on ferroelectric HfZrO₂ metal/ferroelectric/metal (MFM) capacitor and ferroelectric field-effect transistor (FeFET) is demonstrated experimentally with weight transfer, that is, Δ P, per pulse analysis through consecutive alternating potentiation/depression (Pot./Dep.) training pulses. The weight training pulse schemes are studied to have symmetric and linear synapse weight transfer to increase the accuracy and accelerate the deep neural network (DNN) training. With ALD TiN inserted, αp/αd = -0.63/-0.84, asymmetry |αp - αd| = 0.21, and polarization modulation ratio (Pot./Dep.) = 97%/98% are achieved for MFM capacitor, and αp/αd = -1.32/-1.88, asymmetry |αp - αd| = 0.56, and Gmax/Gmin > 10x are delivered for FeFET.
5 January 2017 in IEEE Transactions on Electron Devices
The characteristics of thermal conductivity(k) with different operated temperatures (T), material thicknesses (t), and impurity concentrations (N) are studied by thermoelectric measurements and developed simulation model for the study of self-heating effect. With the input of these module-level material properties in our developed finite-element model, the self-heating effect on the CMOS logic transistors from 20to 5-nm technology nodes are investigated systematically and accurately. The maximum chip temperature in the 14/16-nm technology node Si FinFET device is ~170 °C. On the other hand, the higher operated temperature is also observed in high mobility material devices such as Ge and III-V (InAs) FinFETs due to their poor material properties of k-value. It indicates that these high mobility materials are hard to be used in the next generation scaled technology node devices, unless these devices can be operated at the ultralow voltage bias (<;0.5 V for InAs and <;0.8 V for Ge) from the self-heating effect point of view.
19 February 2018 in Journal of Physics D: Applied Physics
N-type NiO:Al thin films were deposited by RF magnetron sputtering. Their optoelectronic properties versus Al target power was investigated. The results show that with increasing Al target power, the conduction type of NiO films changes from p-type to n-type. The variation of the film’s electrical and optical properties depends on Al amount in the film. When Al target power is relatively low, Al 3+ cations tend to enter nickel vacancy sites, which makes the lattice structure of NiO more complete. This improves the carrier mobility and film’s transmittance. However, when Al target power exceeds 40 W, Al atoms begin to enter into interstitial sites and form an Al cluster in the NiO film. This behavior is beneficial for improving the film’s n-type conductivity but degrades the film’s transmittance. Finally, Al/(p-type NiO)/(n-type NiO:Al)/ITO homojunctions were fabricated. Their performance was compared with Al/(p-type NiO)/ITO heterojunctions without an n-type NiO layer. Thanks to the better interface quality between the two NiO layers, the homojunctions present better performance.
6 August 2018 in IEEE Journal of the Electron Devices Society
Ferroelectric-Hf 1−x Zr x O 2 FETs on silicon on insulator (SOI) are modeled and demonstrated with improvement on subthreshold swing (SS) and hysteresis ( $V_{T}$ -shift), which is based on the capacitance matching concept. The minimum reverse SS = 45 mV/dec and 52 mV/dec are obtained experimentally for SOI and bulk-Si, respectively. The steep SS range (<60 mV/dec) is extended from ~2.5 (bulk-Si) decades to ~3.5 decades SOI. Reverse-drain-induced barrier lowering and negative differential resistance are confirmed at subthreshold region and weak inversion region, respectively.
2 August 2022 in IEEE Transactions on Electron Devices
Through silicon via (TSV) is the key technology for 3-D integrated circuits (3-DICs) which could vertically stack homogeneous or heterogeneous dies with the high performance and density. To evaluate the electrical characteristics of TSV at the high-frequency transmission, the skin effect and surface roughness effect are necessary to be considered. However, these effects would significantly result in the TSV equivalent resistance under the high operating frequency. Thus, it is important to investigate the carbon nano tubes (CNTs) TSV which has less skin effect intrinsically. In this work, we analyze the advantage of CNTs as TSV compared to the conventional filling materials such as copper (Cu). Furtherly, we also propose the equivalent circuit model of TSV and its multi-layer structure to simulate the electrical behaviors with different TSV pitch, height, diameter, and stacking layers by using ANSYS designer and high-frequency structure simulator (HFSS). Based on the frequency-domain analysis, it can be found that CNTs TSV has the lower frequency-dependent loss than Cu due to the lower equivalent resistance. In a summary, CNTs could be a promising TSV filling material at the high-speed transmission frequency based on our study.