High-performance power electronics design requires a firm characterization of active and passive components. This work presents a framework for quantifying passive component performance by reviewing both existing methods and robust device figures-of-merit (FOM). A comprehensive survey yields aggregated data for nearly 700 000 commercial capacitors and inductors of all types. To supplement deficiencies in this data, this work proposes and validates several empirical expressions to estimate passive component energy storage and mass. The estimation of volumetric mass density per component type allows the approximation of component mass from accessible box volume. The estimation of energy-equivalent capacitance in nonlinear Class II ceramic capacitors facilitates the evaluation of stored energy and related energy density FOM. A phenomenological analysis of the comprehensive component data produces several conclusory determinations about peak energy density capabilities—with respect to volume, mass, and cost—across capacitor and inductor technologies.
Additive manufacturing (AM) has the potential to rapidly prototype innovative designs of magnetic components aimed at improving power density and efficiency of switch-mode power converters. However, only a few magnetic feedstocks are available for AM, and the fabricated parts have significantly poorer magnetic properties. Our previous studies showed the promise of an extrusion-based AM platform for making high-performance power magnetics. But, the magnetic paste feedstock developed in these studies suffered from the “slumping” problem, thus not suitable for building large or tall core structures. To improve the AM capability, a ferrite paste was developed that is cured upon ultraviolet (UV) illumination. Core structures with large aspect ratios were fabricated by retrofitting the printer with a UV-light-emitting diode module. By varying the magnetic composition of the paste and sintering the printed parts at and below 1000 °C, we made tall (>4 mm) ferrite cores with relative permeability ranging from 63 to 103 and resonance frequency higher than 30 MHz.
26 March 2018 in IEEE Transactions on Industry Applications
This paper concentrates on the LCL filter with damping resistance intended to connect the shunt active power filter of an active DC-traction substation to the point of common coupling with the transmission grid. In order to find design conditions and conceive a design algorithm, attention is directed to the transfer functions related to currents and the associated frequency response. The mathematical foundation of the design method is based on the meeting the requirements related to the significant attenuation of the high-frequency switching current, concurrently with the unalterated flow of the current that needs to be compensated by active filtering. It is pointed out that there are practical limitations and a compromise must be made between the two requirements. To quantify the extent to which the harmonics to be compensated are influenced by imposing the magnitude response at both highest harmonic frequency to be compensated and switching frequency, a performance indicator is defined. As an additional design criterion, the damping power losses are taken into consideration. The validity and effectiveness of the proposed method are proved by simulation results and experimental tests on a laboratory test bench of small scale reproducing the specific conditions of a DC-traction substation with six-pulse diode rectifier.
28 February 2024 in IEEE Transactions on Power Electronics
This article proposes a switching bus converter, an efficient and compact hybrid switched-capacitor (SC) voltage regulator, for direct 48 V to point-of-load power conversion in data centers. The proposed topology merges a 2-to-1 SC front-end with two eight-branch series-capacitor-buck (SCB) modules through two switching buses. Compared with the existing dc-bus-based architecture, the proposed switching-bus-based architecture does not require dc-bus capacitors, reduces the number of switches, and ensures complete soft-charging operation. In addition, this article conducts a comparative performance analysis of different regulated hybrid SC topologies, which reveals that a larger SC conversion ratio is advantageous for achieving higher performance. Through the two-phase operation of the SCB modules, the proposed topology extends the maximum duty ratio and enables a larger SC conversion ratio. A hardware prototype was designed and built with custom two-phase coupled inductors and synchronous bootstrap daughterboards to validate the theoretical potential of the proposed topology. The hardware prototype was tested up to 500-A output current at 1-V output voltage, achieving 93.4% peak system efficiency, 86.1% full-load system efficiency, and 464-W/in $^{3}$ power density. Moreover, the theoretical benefits of a larger SC conversion ratio were experimentally verified with measured performance at different SC conversion ratios.
28 March 2023 in IEEE Transactions on Power Electronics
To realize high efficiency and high power density for resonant switched capacitor (ReSC) converters, it is critical to have a thorough understanding of the soft-switching mechanism and design the converter appropriately. However, this can be challenging as the soft-switching operation depends on multiple variables and its design difficulty increases quickly with respect to the topology complexity. This paper demonstrates a framework of using geometrical state-plane analysis to facilitate ReSC converter design. The methodology is first applied to a basic 2-to-1 ReSC converter, and then extended to a new 4-to-1 ReSC converter topology we proposed, herein named cascaded multi-resonant converter. This topology has reduced component count thanks to a new “switching bus” architecture. However, it comes at a cost as the converter has multiple resonances within each switching cycle, complicating the soft-switching design. Despite the high circuit complexity, the state-plane analysis neatly provides analytical equations of all state parameters, which are verified by simulations and experiments. Our hardware prototype achieves 6000 W/in 3 power density at 48-to-12 V conversion and 80 A continuous output. Its peak efficiency reaches 99.02%, and full-load efficiency reaches 97.67%, including gate drive loss. Both the power density and efficiency are superior to the state-of-the-art 48-to-12 V solutions.
Conventional design of coupled inductors is focused on a specific converter topology, and the size advantage of coupled inductors over uncoupled inductors is rarely analyzed systematically. This work models the core size for generalized two-phase gapped coupled inductors and provides an effective way to compare the core size for different duty ratios (corresponding to different topologies) and different coupling coefficients. Both the analytical model and hardware prototypes are provided to demonstrate a significant size reduction by using tightly-coupled inductors in hybrid switched-capacitor converters with a large duty ratio. The proposed coupled inductors are applied in a Multi-Level Binary (MLB) Point-of-Load (PoL) converter, achieving 94.4% peak system efficiency and 474 W/in 3 power density with 48-to-1.8 V conversion and 60 A output. Both the efficiency and power density are higher than the conventional MLB-PoL converter using discrete inductors.