Additive manufacturing (AM) has the potential to rapidly prototype innovative designs of magnetic components aimed at improving power density and efficiency of switch-mode power converters. However, only a few magnetic feedstocks are available for AM, and the fabricated parts have significantly poorer magnetic properties. Our previous studies showed the promise of an extrusion-based AM platform for making high-performance power magnetics. But, the magnetic paste feedstock developed in these studies suffered from the “slumping” problem, thus not suitable for building large or tall core structures. To improve the AM capability, a ferrite paste was developed that is cured upon ultraviolet (UV) illumination. Core structures with large aspect ratios were fabricated by retrofitting the printer with a UV-light-emitting diode module. By varying the magnetic composition of the paste and sintering the printed parts at and below 1000 °C, we made tall (>4 mm) ferrite cores with relative permeability ranging from 63 to 103 and resonance frequency higher than 30 MHz.
26 March 2018 in IEEE Transactions on Industry Applications
This paper concentrates on the LCL filter with damping resistance intended to connect the shunt active power filter of an active DC-traction substation to the point of common coupling with the transmission grid. In order to find design conditions and conceive a design algorithm, attention is directed to the transfer functions related to currents and the associated frequency response. The mathematical foundation of the design method is based on the meeting the requirements related to the significant attenuation of the high-frequency switching current, concurrently with the unalterated flow of the current that needs to be compensated by active filtering. It is pointed out that there are practical limitations and a compromise must be made between the two requirements. To quantify the extent to which the harmonics to be compensated are influenced by imposing the magnitude response at both highest harmonic frequency to be compensated and switching frequency, a performance indicator is defined. As an additional design criterion, the damping power losses are taken into consideration. The validity and effectiveness of the proposed method are proved by simulation results and experimental tests on a laboratory test bench of small scale reproducing the specific conditions of a DC-traction substation with six-pulse diode rectifier.
22 June 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Conventional polymeric or organic encapsulants cannot survive long-term operation at high temperatures (>250℃) due to their thermal degradation. In this work, we evaluated an inorganic material, a low-melting-point (Tmelt< 500°C) lead glass, as a potential high-temperature encapsulant for SiC power modules. Processing of the glass on an Al2O3 direct-bond-copper (DBC) substrate was studied, and a stress relief solution was devised to solve the thermal-stress induced glass cracking. The electrical insulation capability of the glass was characterized by measuring partial discharge inception voltage (PDIV). The average PDIV of the glass encapsulated test coupons across a 1 mm gap was > 3 kV at temperatures up to 250°C. The glass encapsulated 1 kV, 36 A SiC MOSFETs showed normal static and dynamic characteristics suggesting the glass did not cause damages to the SiC devices during processing. As for reliability, the glass encapsulant survived a much longer time than several high-temperature polymeric encapsulants (rated temperature >300°C) soaked at 250°C.
Novel designs of magnetic components (inductors and transformers) lead to size reduction of power electronic (PE) systems but are difficult to be fabricated by conventional methods. Additive manufacturing can ease the fabrication of the novel designs that require intricate geometries or multi-permeability cores. The challenge is the lack of functional soft magnetic feedstock/ink with sufficient choices of different permeability or with tailorable permeability. In this study, we explored an easy way to tailor the permeability of a NiCuZn ferrite feedstock by adding different fractions of Co 3 O 4 to the ferrite powder in the feedstock. Toroid cores were 3-D-printed using the feedstock with different fractions of Co 3 O 4 . Relative permeability of the sintered toroid cores could be tailored from 495 to 138 with 0%-0.8% of the Co 3 O 4 . Besides, 0.5% of Co 3 O 4 reduced the core-loss density of the ferrite by 77.6% at a low magnetic flux density of 5 mT. The effects of Co 3 O 4 on saturation flux density, dc bias permeability, electrical resistivity, packing density, and microstructure of the sintered ferrite cores were also characterized. The mechanisms of how Co 3 O 4 affected the magnetic properties of the ferrite feedstock were studied.
29 August 2017 in IEEE Transactions on Industry Applications
We used gelcasting, a pressure-less processing technology for fabricating ceramic parts, to make NiCuZn ferrite cores, which are traditionally made by a process that requires high hydrostatic pressure. A commercial NiCuZn ferrite powder was mixed with water, dispersant, and organic monomers to form a slurry, and then cast it into a mold of toroid shape followed by sintering at 900 °C, 950 °C, and 1000 °C for two hours. The sintered core mass density was found to increase with sintering temperature. The magnetic properties of the cores, i.e., complex permeability and core-loss density, were measured. We found that the real part of the permeability increased with sintering temperature from about 44 at 900 °C to 78 at 1000 °C. The core-loss density data at 5 MHz showed that the cores sintered at 950 °C had the lowest core-loss density; approximately 50% lower than that of a commercial NiZn ferrite (4F1) core. Since gelcasting does not require pressure and is scalable and low cost, it has the potential to make magnetic cores with intricate shapes and sizes for desired coupling of magnetic fluxes to improve efficiency and power-density of power electronics converters.
24 May 2021 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Coupled inductors are used in power electronics to improve transient response and reduce component size. To further increase inductance density and reduce fringing fields, a combination of different magnetic materials was introduced to create a hetero-magnetic coupled inductor (HMCI) core. To simplify and speedup the prototyping of HMCI designs, in this study a paste-extrusion additive manufacturing platform was used to co-process a custom-developed magnetic and conductive feedstock. First, ferrite plates of each having a winding were co-printed and co-sintered. Then, the HMCI was assembled by bonding together the ferrite + winding plates using a low-temperature curable magnetic paste. The finished HMCI was characterized by measuring its dc winding resistances, leakage inductance, and coupling coefficient. The coupling coefficient of the HMCI was easily adjustable to meet various requirements for high-frequency interleaved multiphase buck converters. This work demonstrates the feasibility of applying an additive manufacturing process for rapid prototyping of an unconventional power magnetic component having an inhomogeneous magnetic core.