This study focused on the experimental drying of Bo Chinh ginseng by the ultrasound-assisted heat pump drying method, in which the effects of drying air temperature (T), ultrasonic power (P), intermittency ratio of ultrasound generator (A) on the moisture effective diffusion coefficient (Deff), saponin content (Sp) and color change (dE) during the drying process were determined. The results showed that the drying time was reduced from 12.5 h at 35 °C to 8.9 h at 40 °C and greatly reduced to 5.8 h at 55 °C. The moisture diffusion coefficient Deff and color change index increased with the increase in drying temperature. Meanwhile, from 35 °C to 45 °C, the saponin content after drying tended to increase gradually, but when the temperature continued to rise from 45 °C to 55 °C, the saponin content decreased. The effect of ultrasonic power in the drying process was in particular as follows. The drying time of 8.8 h at 40 W ultrasonic power reduced to 7.8 h at 80 W ultrasonic power, and reduced to 7 h at 160 W ultrasonic power. The remaining saponin content after drying tended to increase gradually at the power level of 40–120 W (from 89.2% to 95.2%) and decrease when the power increased from 120 to 160 W (from 95.2% to 90.5%). The moisture diffusion coefficient Deff also increased with the increase in ultrasonic power. Meanwhile, the color change of dried products decreased as the ultrasonic power increased in the range of 40–120 W but increased with the ultrasonic power range from 120 to 160 W. Additionally, the experimental method and Box–Behnken design were used for optimizing the drying process with the optimal drying conditions such as drying air temperature of 45.2 °C, ultrasonic power of 127.7 W and intermittency ratio of ultrasound generator of 0.18.
The study focused on reviewing modern and effective drying methods assisted by infrared radiation, microwave and radio frequency. In which, the drying results of previous studies were reviewed to clarify the drying efficiency of drying methods with the support of infrared radiation, microwave and radio frequency. The review results showed that the radiant heating mechanism of infrared radiation and the volumetric heating mechanism of microwave and radio frequency supported the process of material heating and moisture diffusion within the material. As a result, the drying process achieved high drying efficiency, the drying time was significantly shortened and the quality of the dried products was improved both in terms of sensory quality and nutritional quality. The study of the application of infrared radiation, microwave and radio frequency in drying technique had a high scientific, technological and practical significance. This would be the foundation for finding suitable drying methods and drying modes to improve drying efficiency as well as the quality of dried products.
This study focused on an engineering problem of heat and mass transfer in infrared (IR) assisted heat pump (HP) drying of purple yam including both a drying experiment and theory of heat and mass transfer mathematical equations. The experimental drying of yam by the IR assisted HP drying method was performed to evaluate the effect of IR power on drying rate and heating rate. The input drying parameters included the drying air temperature of 50°C, drying air velocity of 2.5 m·s −1 and IR power of 0, 300 and 350 W, in which, at the IR power of 0 W, the HP-only drying mode was performed. The experimental drying results showed that the IR assisted HP drying method could improve the drying rate and heating rate as compared to HP-only drying. At the IR power of 350 W, the drying time was the shortest (150 minutes), followed by the IR power of 300 W (210 minutes) and HP-only drying (300 minutes). The IR assisted HP drying obtained the high heating rate as the time required for the drying material to reach the drying temperature was about 35 and 25 minutes corresponding to the IR power of 300 and 350 W. While in HP-only drying, it took about 270 minutes for the drying material’s temperature to reach nearly the drying air temperature value. Besides, the comparison between the predicted data by numerically solving the heat and mass transfer equations and experimental drying data was also conducted. The analysis results indicated that the predicted data could be used to predict the experimental data accurately. The theoretical results of heat and mass transfer in the IR assisted HP drying process as well as experimental drying results would be the basis for improving the IR assisted HP drying equipment to achieve the drying efficiency including the drying rate, quality of dried products, and energy consumption.
The study focused on the orientations of building sustainable new rural areas associated with urbanization. This was very necessary, in order to develop a concentrated, commodity agriculture and to form residential areas and infrastructure, which were suitable to the process of industrialization and modernization of agriculture and rural areas. The agricultural sector was restructured, and the living conditions of rural people were improved close to those in urban areas. The project of the National Target Program on building new rural areas in Vietnam was analyzed. The program has achieved many expected results. In which, the construction of new rural areas has achieved great achievements. The basic socioeconomic infrastructure in the rural areas was strengthened in a synchronous direction. The sustainable development of the rural economy was in the direction of increasing added values and raised people’s incomes and gradually narrowed the gap between rural and urban areas. The work of landscape construction, implementation of environmental sanitation had a remarkable change.
This study focused on the thin-layer drying of yam by infrared-assisted heat pump drying to determine the thin-layer drying model, the effective moisture diffusivity, and the activation energy of moisture within the yam. The thin-layer drying experiment was conducted with input drying parameters such as drying temperatures of 40, 45, and 50°C, drying air velocity of 2.5 m·s⁻¹, and infrared power of 250, 300, and 350 W. In order to determine a suitable thin-layer drying model for describing the yam drying process, six different thin-layer drying models (Lewis, Page, Modified Page, Henderson and Pabis, Wang and Singh, and Midilli) were chosen for nonlinear regression with the experimental drying data. The Midilli model was found to be the most suitable drying model for describing the thin-layer drying of yam. The average effective moisture diffusivity was in the range of 4.184×10⁻⁹ to 8.142×10⁻⁹ m²·s⁻¹, and the activation energy was in the range of 16.78 to 21.01 kJ·mol⁻¹ over the proposed range of drying input parameters
1 December 2023 in IOP Conference Series: Earth and Environmental Science
The study focused on the efficiency of radio frequency (RF) assisted heat pump (HP) drying of shrimp. The experimental drying was conducted with input drying parameters as the drying-air temperature of 45°C, the drying-air velocity of 2.0 m/s, and RF power of 0, 0.5 and 1.0 kW, in which, HP only drying was corresponding to RF power of 0 kW. In the study, the effect of RF power on drying rate, color change, and protein content of dried shrimp were considered. When RF power increased, the drying rate and protein retention of dried shrimp increased significantly. At RF power of 1.0 kW, the drying time was 260 minutes, that reduced about 19% and 38% as compared to RF power of 0.5 and 0 kW. The protein content of shrimp after drying was 62.06%, 66.02% and 69.87% corresponding to the drying modes at RF power of 0, 0.5 and 1.0 kW. Besides, in RF assisted HP drying, the shrimp samples after drying got better color, appearance, and taste than those of HP only drying. At RF power of 1.0 kW, the dried shrimp got the best redness and lightness color, followed by the drying modes at RF power of 0.5 and 0 kW. In both RF assisted HP drying and HP only drying, the dried shrimp surface was not cracked, and the dried products obtained the good taste and the level of redness and lightness required.