In this study, drying kinetics, including thermal and moisture, of Codonopsis javanica with the support of ultrasonic technology in the drying process were investigated. Experimental processes were carried out at drying air temperatures of 40°C, 45°C, and 50°C with and without ultrasound at a frequency of 20 kHz and three levels of intensity: 1.3 kW/m2, 1.8 kW/m2, and 2.2 kW/m2. Based on theoretical calculations, experimental data, and the particle swarm optimization (PSO) algorithm, the coefficient of thermal diffusion was determined in the range of 1.01–1.36 × 10−7 m2/s, and the coefficient of moisture diffusion is in the range of 3.2–6.7 × 10−10 m2/s. In addition, the color parameters (,, and ) of the drying materials were also considered. Results showed the overall color differences (∆E) of dried products change in the range of 8.0–12.9 compared with the fresh ones. In this work, the multiple boundary conditions were considered to determine the moisture and thermal diffusion coefficients; the results obtained prove that the quality of dried products in terms of color change is also improved.
After the centrifugation stage, refined salt particles have rather high moisture content; therefore, the moist salt particles in contact with each other will stick together in a short time. In particular, the moist salt particles will stick together faster and tighter and form a larger unit when they are exposed to drying hot air. For this reason, the refined salt was dried by rotary drum dryers with vibrating balls distributed along the drum or a vibrating fluidized bed dryers. These drying methods make poor product sensory quality, low product recovery efficiency, while also lead to an increase of heat and electricity energy consumption. In order to increase the efficiency of refined salt drying technology by conventional continuous fluidized bed dryers, the chapter focuses on the study of aerodynamic properties of refined salt grains in the continuous fluidized particle layer. The content of the chapter presents theoretical and empirical methods to determine fluidization velocity types in designing a continuous fluidized bed dryer.
This study focused on an engineering problem of heat and mass transfer in infrared (IR) assisted heat pump (HP) drying of purple yam including both a drying experiment and theory of heat and mass transfer mathematical equations. The experimental drying of yam by the IR assisted HP drying method was performed to evaluate the effect of IR power on drying rate and heating rate. The input drying parameters included the drying air temperature of 50°C, drying air velocity of 2.5 m·s −1 and IR power of 0, 300 and 350 W, in which, at the IR power of 0 W, the HP-only drying mode was performed. The experimental drying results showed that the IR assisted HP drying method could improve the drying rate and heating rate as compared to HP-only drying. At the IR power of 350 W, the drying time was the shortest (150 minutes), followed by the IR power of 300 W (210 minutes) and HP-only drying (300 minutes). The IR assisted HP drying obtained the high heating rate as the time required for the drying material to reach the drying temperature was about 35 and 25 minutes corresponding to the IR power of 300 and 350 W. While in HP-only drying, it took about 270 minutes for the drying material’s temperature to reach nearly the drying air temperature value. Besides, the comparison between the predicted data by numerically solving the heat and mass transfer equations and experimental drying data was also conducted. The analysis results indicated that the predicted data could be used to predict the experimental data accurately. The theoretical results of heat and mass transfer in the IR assisted HP drying process as well as experimental drying results would be the basis for improving the IR assisted HP drying equipment to achieve the drying efficiency including the drying rate, quality of dried products, and energy consumption.
Radio Frequency (RF) dielectric heating using in drying has obvious advantages such as reducing drying time, volumetrically uniform heating and improving product quality. A RF generator applied in drying technology was designed, manufactured and tested for drying Ganoderma lucidum. The drying experiments were conducted by two drying methods include heat pump drying and RF assisted heat pump drying in order to inspect the operating parameters of the RF generator and to evaluate the effect of the drying methods. The results shown that the operating parameters of RF generator got the design requirement, such as operating capacity of 3 kW and operating frequency of 27 MHz. The drying time of RF assisted heat pump drying process was about 7 hours to achieve material moisture content of 13% (w.b) that was less drying time than heat pump drying process, the Ganoderma Lucidum retained its color and flavor and Polysaccharide content after drying was 0.881%.
The research aimed to determine the effect of different drying methods including heat pump drying, hot air drying, combined infrared and heat pump drying, and combined infrared and hot air drying on the quality of one-sun-dried squid. With each method, squids are dried at three temperature degree of 40, 45 and 50°C. The quality of the product is assessed by protein content, organoleptic quality and drying rate. The research results showed that combined infrared and heat pump drying at temperature of 45°C is the most appropriate method of drying one-sun-dried squid. After drying, the protein content reaches 22/100 gram-squid; drying time is 180 minutes, the average drying rate is 3.33 %H 2 O/h and the squids color is best retained.