Chemical dust suppression is an effective dust control technology. A dust suppressant component evaluation method that facilitates a complete selection of safe, efficient, and economical chemical materials has not been explored. Considering dust suppression performance, environmental safety, and cost-effectiveness of chemical dust suppressant technology, this study constructs a comprehensive evaluation index system of chemical dust suppressant performance, including the wetting performance, hygroscopic performance, bonding performance, annual cost per unit area, pH value of dust suppression solution, chemical toxicity, and chemical corrosion. Among them, the index characterizing the wetting performance of the solution is the sedimentation wetting time, which is determined by the dust sedimentation experiment; the index characterizing the hygroscopic performance of the solution is the evaporation stability time, which is determined by the evaporation experiment of the solution on the dust surface; the index to characterize the bonding performance of the solution is the surface wind erosion rate, which is determined by the wind erosion experiment of the solution on the dust surface; the toxicity of the solution is evaluated by the LD50 of the solution; the index to characterize the corrosion performance of the solution is the Q235 monthly steel corrosion rate, which is determined by the Q235 steel corrosion test. Corresponding evaluation parameters are determined including sedimentation wetting time, evaporation stabilization time, surface wind erosion rate; annual average use cost per unit area; solution pH value, chemical acute toxicity classification, monthly corrosion rate of Q235 steel, and corresponding standard test methods are also provided. In order to evaluate the comparability of the results, according to the specific requirements of the evaluation index system and the distribution characteristics of the measurement data, the data of each evaluation and detection index are standardized by linear transformation, range transformation and other methods, so that the obtained results are comparable. Considering the differences in the actual performance requirements of dust suppressants in different usage scenarios, the weights of evaluation indicators at all levels can be set independently and flexible. The experimental test data obtained through the example shows that: among the four chemicals selected to participate in the experiment, the comprehensive dust suppression performance score of Triton X-100 solution is in the poor-grade category. The comprehensive dust suppression performances of calcium chloride solution, water, and polyacrylamide solution scored high in the average-grade category. The comprehensive evaluation process is logically correct, and the results are consistent with the phenomena observed in the experiment, consistent with conventional understanding, and have strong credibility. This method can provide a standardized evaluation technique and test process for the comprehensive performance evaluation and comparison of chemical materials and dust suppressants.

In this paper, a nano-composite dust suppressant has been proposed to make up for the deficiency in wettability and moisturizing performance of a nanofluid dust suppressant. The nanometer material Al₂O₃, super absorbent polymer, carboxyl methyl starch sodium, and polyacrylamide were selected as effective components of it. The surface tension of the solution, evaporation resistance, and uniaxial compressive strength (UCS) were chosen as evaluation index to compare the suppression performance, these dust suppressants include the water, nanofluid dust suppressant and nano-composite dust suppressant, and the surface morphology of each tested material was observed by micro image analysis system. It was found that the surface tension and water loss rates of the nano-composite dust suppressants, respectively, decreased by 31.96% and 7.1%, and the maximum UCS increased by 31.82% compared with data of nanofluid dust suppressants. Since the nano-composite dust suppressant has good dispersion, permeability and bond performance, the suppressant film has fewer micro-cracks from the photos of microscopic image; it can improve the compactness and integrity of dust consolidation to prevent the evaporation of water and dust re-entrainment.

The aim of this study was to assess the total concentration and speciation variation of heavy metals (Pb, Cd, Cu and Zn) during composting and vermicomposting of industrial sludge with different addition rations of rice husk biochar. Results indicated that pH, EC, total phosphorus (TP) and total potassium (TK) were increased and total organic carbon (TOC) and total nitrogen (TN) were decreased during the composting of industrial sludge with biochar compared with the control (sludge without biochar). The addition of earthworm to the biochar-amended sludge further decreased pH and TOC but highly enhanced the EC, TN, TP and TK. Comparatively lower concentrations of total and DTPA-extractable heavy metals were observed in biochar-amended sludge treatments mixed with earthworm in comparison with the biochar-amended sludge treatments without earthworm or the control. Sequential extraction methods demonstrated that vermicomposting of sludge with biochar converted more metals bound with exchangeable, carbonate and organic matter into the residual fraction in comparison with those composting treatments of sludge with biochar. As a result, the combination of rice husk biochar and earthworm accelerated the passivation of heavy metals in industrial sludge during vermicomposting. Rice husk biochar and earthworm can play a positive role in sequestering the metals during the treatment of industrial sludge. This research proposed a potential method to dispose the heavy metals in industrial sludge to transform waste into resource utilization.

In order to study the air volume distribution regularity of mine ventilation clothing, the influence of ventilation clothing of different pipeline structures on air flow distribution is discussed. By establishing the simulation models of three different structures and using software simulation, the air volume distribution under different ventilation air volume and different pipeline structures is analyzed; the relationship between the air volume of the pipelines and the frictional resistance along the course is studied. The results demonstrated that the air volume of the pipelines farther from the ventilation inlet in the transverse type and longitudinal type is larger, while the air volume of the pipelines close to the ventilation inlet is smaller, and the air volume of the intermediate pipelines is medium and relatively stable; regularity of air volume distribution in pipelines: transverse type > spiral type > longitudinal type. Total air volume in the ventilation tubes: spiral type > longitudinal type > transverse type, with the increase of ventilation volume, the air volume in the spiral type tube increases greatly, and a small increase in air volume for transverse type and longitudinal type. Based on the data obtained from the transverse type simulation, the air volume of the pipelines airflow is inversely proportional to the frictional resistance along the course.