During the manufacturing of welded structures, some degree of residual stresses occurs. The classic approach to residual stress reduction is Post-Weld Heat Treatment (PWHT). In the case of structural grade mild steels, the thermal process is well established. In case of S690QL1 High Strength Steel (HSS), which is manufactured using the Quenching and Tempering (QT) process considered in this paper, only limited PWHT treatment is possible without deterioration of mechanical properties. Since this steel grade is susceptible to subsequent heat input, the challenge is to establish adequate PWHT parameters, achieving residual stress reduction while retaining sufficiently high mechanical properties. The paper considers X joint welded HSS steel plates with slightly overmatching filler metal. The welded coupon is prepared and subjected to PWHT treatment. The research on the influence of heat treatment was performed using the four different PWHT cycles and initial As-Welded (AW) material condition. The authors proposed those PWHT cycles based on available resources and the literature. Process holding temperature is considered the variable parameter directly related to the behaviors of material properties. The methodology of welded joint analysis includes experimental testing of mechanical properties, metallographic examination, and residual stress quantification. Testing of mechanical properties includes tensile testing, Charpy V-notch impact testing, and hardness testing in scope of complete welded joint (BM + HAZ + WM). Metallographic examination is performed in order to characterize the welded joint material in relation to applied PWHT cycles. In order to quantify residual stresses, all heat-treated samples were examined via the X-ray diffraction method. Mechanical properties testing determined that an increase in PWHT cycle holding temperature leads to degradation of tested mechanical properties. For specific zones of the welded joint, the decreasing trend from AW condition to Cycle D (max. 600 °C) can be quantified. Based on representative specimens comparison, strength values (BM ≤ 5.7%, WM ≤ 12.1%, HAZ ≤ 20%), impact testing absorbed energy (BM = 17.1%, WM = 25.8%, FL = 12.5%, HAZ = 0.6%), and hardness values (BM = 4.1%, WM = 3.2%, CGHAZ = 16.6%, HAZ = 24.2%) are all exhibiting decrease. Metallographic examination, using the light microscopy, after the exposure to PWHT thermal cycles, did not reveal significant changes in the material throughout all specific welded joint segments. Average relative reduction in residual stress in correlation with PWHT temperature can be observed (AW = 0%, Cycle A (max. 400 °C) = 72%, Cycle B (max. 530 °C) = 81%, Cycle C (max. 550 °C) = 93% and Cycle D (max. 600 °C) = 100% stress reduction). It can be concluded that S690QL1 HSS welded joints can generally be subjected to PWHT, while adhering to the limits of the material and process. In the authors’ shared opinion, it is advisable to use the PWHT Cycle C (max. 550 °C) with 93% RS reduction, while mechanical properties retain high values.

The plasma jet cutting process has a high potential for the machining of aluminium and its alloys. Aluminium is well known as a highly thermally conductive and sensitive material, and because of that there exist uncertainties in defining process parameters values that lead to the best possible cut quality characteristics. Due to that, comprehensive analysis of process responses as well as defining optimal cutting conditions is necessary. In this study, the effects of three main process parameters—cutting speed, arc current, and cutting height—on the cut quality responses: top kerf width, bevel angle, surface roughness Ra, Rz, and material removal rate were analyzed. Experimentations were conducted on aluminium EN AW-5083. In order to model relations between input parameters and process responses and to conduct their optimization, a novel hybrid approach of response surface methodology (RSM) combined with desirability analysis was presented. Prediction accuracy of developed responses regression models was proved by comparison between experimental and predicted data. Significance of process parameters and their interactions was checked by analysis of variance (ANOVA). Desirability analysis was found as an effective way to conduct multi-response optimization and to define optimal cutting area. Due to its simplicity, the novel presented approach was demonstrated as a useful tool to predict and optimize cut quality responses in plasma jet cutting process of aluminium alloy.

The development of corrosion mechanisms is a major issue that industrial experts are faced with while dealing with all phases of metal exploitation. Damage caused by corrosion affects the increase in both direct and indirect costs of manufacture. With adequate surface protection technology, it is possible to lessen the intensity of corrosion mechanisms’ development. In order for the selected surface protection technology to provide its full protective action, it is necessary to be familiar with its process parameters. This paper deals with a surface protection system that creates a barrier between the aggressive environment and the base material. The tested barrier was created on a base material surface by electrostatic powder spraying. In this experiment, three types of base material (carbon steel, aluminum and galvanized steel) were coated by applying different combinations of operating parameters. Operating parameters, i.e., the voltage and strength of the electric current, were taken as numerical input variables in the experiment. Each experiment design was focused on measuring the thickness of the protective layer. Analysis of the obtained results and statistical data processing confirmed that appropriate parameters (input variables) provided the target thickness of the protective coating on each of the tested materials. Optimization of parameters contributes to the efficiency of production, shortens the processing time and ensures that coating thickness stays within the limits defined either by the manufacturer or the end user.

In microalloyed steels, plastic instabilities often appear which have been found to be associated with changes in the microstructure. In this paper, research was carried out on the influence of the microstructure in different areas of the deformation zone during the formation of Lüders bands in niobium microalloyed steel. Thermography and digital image correlation during static tensile testing were used to research deformation behavior and the area before and during the formation of the Lüders band. Different local values of temperature changes, i.e., stress changes, and strains in the examined areas during the formation of the Lüders band were determined. The highest values of the temperature changes and strains during the formation of the Lüders band were measured in the area of the initial appearance of the Lüders band. In order to clarify the observed changes, a microstructural analysis, using X-ray diffraction, scanning electron and transmission electron microscopy methods, was used. It was established that the observed temperature, i.e., stress, and strain changes are related to changes in the microstructure. The analyses of changes in the microstructure, arrangement and interaction of dislocations with precipitates revealed significant changes in the movement of dislocations and their interaction with fine niobium-containing precipitates during the formation of Lüders bands. The influence of microstructural parameters on the Lüders band formation in niobium microalloyed steel has been established based on this research.

This research reveals the influence of different purging conditions on the fusion zone dimensions and shape for stationary autogenous TIG welding of 316L stainless steel. Welding experiments were performed for unpurged and purged weld root side for 7...

In order to determine the Lüders band propagation along the deformation zone length and width as affected by the force action direction, a detailed line analysis is performed by applying thermography and digital image correlation (DIC) during static...