This paper presents a thermal/RF hybrid energy harvester. The energy harvesting system can scavenge energy from a thermoelectric generator (TEG) and a radio-frequency (RF) energy source simultaneously, and deliver the combined power to a single load. Two techniques are employed in the system to increase the end-to-end efficiency; the rectifying-combination technique is proposed to eliminate the power loss associated with a dedicated AC-DC converter before the combiner and an improved fractional open-circuit voltage (FOCV) maximum power tracking (MPPT) is considered for a high average efficiency. A dynamic power path control extracts the maximum RF power from a cross-coupled differential rectifier, and also behaves as an AC/DC energy combiner. The thermal/RF harvester system achieves a measured peak end-to-end power conversion efficiency (PCE) of 63.4%. The shorter sampling time of 26ms every 16s for the proposed FOCV MPPT method reduces the long charging tail required to refresh the sampling capacitor, resulting in a an improved average efficiency of 82.2% for the thermal harvester. Fabricated in 0.18 μm CMOS technology, the prototype operates at a thermal input voltage ranging from 40 mV to 400 mV and an RF power from -18 dBm to -3 dBm and delivers an output voltage of 1.8 V. The total area of the fabricated circuit prototype is 1.22 mm².
23 July 2010 in IEEE Journal of Solid-State Circuits
This paper proposes the use of N-push operation for combining the functions of the VCO and divider in the mm-wave frequency range. If employed in a PLL, the combined VCO/divider (C-VCO/D) would potentially provide wider tuning range than traditional mm-wave PLLs employing injection locked frequency dividers, thus exploiting the full range available in the 60 GHz band (57 GHz-64 GHz). The behavior of triple push oscillators based on injection locking theory is analyzed to study their various oscillation modes, their stability and the effect of mismatch on the oscillator performance. Design guidelines are provided for boosting the third harmonic power at a given power budget. Using 130 nm IBM CMOS technology, multiple versions of the triple push oscillator are implemented and characterized. A 55 GHz-65 GHz tuning range is obtained using a 206 pH tank inductance and requires Icore = 20 mA, and Ibuffer = 15 mA from a 1.4 V supply. For a tank inductance of 140 pH, a 63.2 GHz-72.4 GHz tuning range is obtained using Icore = 17 mA, and Ibuffer = 18 mA with a phase noise of -91 dBc/Hz at 10 MHz from the 63.2 GHz carrier and -95 dBc/Hz at 10 MHz from the 72.4 GHz carrier.
30 January 2018 in IEEE Transactions on Circuits and Systems I: Regular Papers
An inductorless 10-Gb/s optical receiver including a novel transimpedance amplifier (TIA) with dual feedback loop and a limiting amplifier with third-order nested feedback is presented. The current-buffer-based TIA employs an active Cherry-Hooper stage in the auxiliary amplifier and reuses the tail current source to achieve 10 Gb/s operation in the presence of a 1 pF photodiode input capacitance. Systematic analysis and design methodology of the double loop TIA is given with simple design equations derived for optimizing the performance of each loop. The use of nested feedback in the four stage limiting amplifier enables a gain-bandwidth-product >1 THz without the use of on-chip inductors. It is shown that the proposed limiting amplifier circuit enhances bandwidth by utilizing inherent equalization between the overdamped and underdamped poles. Implemented in IBM 130-nm CMOS technology, the optical receiver achieves a BER <10⁻¹² at 10 Gb/s for an input current of 30 μAp-p in electrical measurement, delivering 600 mVp-p at the output of the 50-Ω buffer. Optical testing confirmed -17.4 dBm sensitivity for a data rate of 7.5 Gb/s, which is limited by the maximum speed of the 850-nm source available at the time of measurement. The receiver dissipates 108 mW from 1.2-V supply (excluding the output buffer) and occupies a core area of only 0.08 mm².
In this paper, a twin-FET (field effect transistor) THz detector monolithically integrated with a dual-feed antenna is presented. The antenna-detector configuration can be extended for ’N’ FET elements to relax the input impedance requirement for the detector readout circuitry while maintaining good responsivity. A dual-feed octagonal slot antenna is used to couple THz radiation and provide differential excitation to the twin-FET detector. The multi-feed antenna-FET detector interface can be designed for an arbitrary phase excitation of one or more FET elements. Fabricated in Global Foundries 22nm FD-SOI process, the proposed detector covers a measured frequency range from 220 GHz to 300 GHz. Such bandwidth is sufficiently wide to capture reliable spectral information for distinguishing a number of gases in a mixture. The absorption spectra of pure methanol, chloromethane and acetonitrile are measured using a rotational spectroscopy setup incorporating the twin-FET detector. Detection of a small concentration of acetonitrile, at 4 Torr pressure, is demonstrated in a binary mixture with predominantly chloromethane. Detection of ethanol and methanol in their binary mixture is also demonstrated at 4 Torr pressure. This is a significant step towards the development of all-electronic THz spectroscopy for the detection of volatile organic compounds (VOCs) in the presence of contaminants with a strong THz absorption signature at > 1 Torr pressure.
Silicon-based kinetic energy converters employing variable capacitors, also known as electrostatic vibration energy harvesters, hold promise as power sources for Internet of Things devices. However, for most wireless applications, such as wearable technology or environmental and structural monitoring, the ambient vibration is often at relatively low frequencies (1–100 Hz). Since the power output of electrostatic harvesters is positively correlated to the frequency of capacitance oscillation, typical electrostatic energy harvesters, designed to match the natural frequency of ambient vibrations, do not produce sufficient power output. Moreover, energy conversion is limited to a narrow range of input frequencies. To address these shortcomings, an impacted-based electrostatic energy harvester is explored experimentally. The impact refers to electrode collision and it triggers frequency upconversion, namely a secondary high-frequency free oscillation of the electrodes overlapping with primary device oscillation tuned to input vibration frequency. The main purpose of high-frequency oscillation is to enable additional energy conversion cycles since this will increase the energy output. The devices investigated were fabricated using a commercial microfabrication foundry process and were experimentally studied. These devices exhibit non-uniform cross-section electrodes and a springless mass. The non-uniform width electrodes were used to prevent pull-in following electrode collision. Springless masses from different materials and sizes, such as 0.5 mm diameter Tungsten carbide, 0.8 mm diameter Tungsten carbide, zirconium dioxide, and silicon nitride, were added in an attempt to force collisions over a range of applied frequencies that would not otherwise result in collisions. The results show that the system operates over a relatively wide frequency range (up to 700 Hz frequency range), with the lower limit far below the natural frequency of the device. The addition of the springless mass successfully increased the device bandwidth. For example, at a low peak-to-peak vibration acceleration of 0.5 g (peak-to-peak), the addition of a zirconium dioxide ball doubled the device’s bandwidth. Testing with different balls indicates that the different sizes and material properties have different effects on the device’s performance, altering its mechanical and electrical damping.