We report the electroluminescence (EL) characteristics of blue ultra-thin emissive layer (U-EML) phosphorescent (PH) organic light-emitting diodes (OLED) and thermally activated delayed fluorescence (TADF) OLED. A variety of transport layer (TL) materials were used in the fabricated OLEDs. The well-known FIrpic and DMAC-DPS were used with a thickness of 0.3 nm, which is relatively thicker than the optimal thickness (0.15 nm) of the blue phosphorescent ultra-thin emissive layer to ensure sufficient energy transfer. While FIrpic showed overall high efficiency in various TLs, DMAC-DPS exhibited three times lower efficiency in limited TLs. To clarify/identify low efficiency and to improve the EL, the thickness of DMAC-DPS was varied. A significantly higher and comparable efficiency was observed with a thickness of 4.5 nm, which is 15 times thicker. This thickness was oriented from the TADF itself, which reduces quenching in a triplet–triplet annihilation compared to the PH process. The thinner optimal thickness compared with ~30 nm of fluorescent OLEDs suggests that there still is quenching taking place. We expect that the efficiency of TADF U-EML OLEDs can be enhanced through further research on controlling the exciton quenching using multiple U-EMLs with spacers and a novel material with a high energy transfer rate (ΔES-T).
This study investigates the application of scattering structures to the metal layer in a DMD (Dielectric/Metal/Dielectric) configuration through plasma treatment. The purpose is to enhance the light extraction efficiency of organic light-emitting diodes (OLEDs). Different plasma conditions were explored to create scattering structures on the metal layer. The fabricated devices were characterized for their electrical and optical properties. The results demonstrate that the introduction of scattering structures through plasma treatment effectively improves the light extraction efficiency of OLEDs. Specifically, using O2-plasma treatment on the metal layer resulted in significant enhancements in the total transmittance, haze, and figure of merit. These findings suggest that incorporating scattering structures within the DMD configuration can effectively promote light extraction in OLEDs, leading to enhanced overall performance and light efficiency.
In this study, various diffusers are applied to highly efficient ultra-thin emission layer (EML) structure-based blue phosphorescent organic light-emitting diodes (PHOLEDs) to improve the electroluminescence (EL) characteristics and viewing angle. To achieve highly efficient blue PHOLEDs, the EL characteristics of ultra-thin EML PHOLEDs with the various diffusers having different structures of pattern–shape (hemisphere/sphere), size (4~75 μm), distribution (surface/embedded), and packing (close-packed/random) were systematically analyzed. The diffusers showed different enhancements in the overall EL characteristics of efficiencies, viewing angle, and others. The EL characteristics showed apparent dependency on their structure. The external quantum efficiency (EQE) was enhanced mainly by following the orders of pattern, size, and shape. Following the pattern size, the EQE enhancement gradually increased; the largest-sized diffuser with a 75 μm closed-packed hemisphere (diffuser-1) showed a 1.47-fold EQE improvement, which was the highest. Meanwhile, the diffuser with a ~7 μm random embedded sphere with a low density (diffuser 5) showed the lowest 1.02-fold-improved EQE. The reference device with ultra-thin EML structure-based blue PHOLEDs showed a maximum EQE of 16.6%, and the device with diffuser 1 achieved a maximum EQE of 24.3% with a 5.1% wider viewing angle compared to the reference device without a diffuser. For the in-depth analysis, the viewing angle profile of the ultra-thin EML PHOLED device and fluorescent green OLEDs were compared. As a result, the efficiency enhancement characteristics of the diffusers show a difference in the viewing angle profile. Finally, the application of the diffuser successfully demonstrated that the EL efficiency and viewing angle could be selectively improved. Additionally, we found that it was possible to realize a wide viewing angle and achieve considerable EQE enhancement by further investigations using high-density and large-sized embedded structures of light-extraction film.
In this study, we demonstrated organic light-emitting diodes (OLEDs) outcoupling with a flexible polydimethylsiloxane (PDMS) film with a micro-convex structure using the breath figure (BF) method. We can easily control the micro-convex pattern by adjusting the concentration of polystyrene and the humidity during the BF process. As process conditions to fabricate the micro-convex structure, polymer concentrations of 10, 20, 40, and 80 mg/mL and 60, 70, and 80% relative humidity were used. To evaluate the optical properties, we analyzed the transmission, diffusion, and electroluminescence with or without the micro-convex structure on the OLEDs. The shape and density of the micro-convex structure are related to its optical properties and outcoupling and we have experimentally demonstrated this. By applying a micro-convex structure, it achieved up to a 42% improvement in the external quantum efficiency compared to bare OLEDs (without any light extraction film). We expect the fabricated flexible light extraction film to be effective for outcoupling and applicable to flexible devices.
In this study, we fabricated a nanostructure on the surface of the micro-lens array (MLA), which is one of the light extraction technologies of organic light-emitting diodes (OLEDs), by performing the Reactive Ion -Etching (RIE) process. The MLA consists of a lensed area and a lens-less bottom (flat film area). We performed a systematic analysis to find ways to improve the light extraction efficiency of the MLA surface and flat film area. By controlling the RIE process time and type of gas plasma, nanostructures were formed on the surface of the MLA. O2 and CF4 gas plasmas resulted in nanostructures with tall heights and high aspect ratios, whereas CHF3 and Ar gas plasmas resulted in nanostructures with small heights and low aspect ratios. Furthermore, it was found that the nanostructures were not covered over the entire area, and the extent to which the nanostructures were distributed varied depending on the process time. As the RIE process time increases, the nanostructure expands from the top surface of the MLA to the flat film area. This limited the light extraction efficiency improvement. At a short process time of 50 s, nanostructures were formed only on the upper surface of the MLA hemisphere, which increased the light extraction efficiency. However, at long process times over 50 s, the surface of the hemisphere of MLA was covered with vertically aligned nanostructures, which decreased the efficiency. While the flat film area was covered with nanostructures at the longest process time of ~3200 s, it was effective, but the total efficiency was further decreased by the trade-off between them. As a result, the high-aspect-ratio nanostructured MLA patterned only on the top surface of the hemispherical MLA with a 50 s O2 plasma treatment showed the highest efficiency, which was slightly higher than that of the bare MLA. We expect that if the nanostructures can be formed in a direction perpendicular to the MLA surface and the flat film area simultaneously, the light extraction efficiency would be further improved.
Quantum dots (QDs) have tremendous potential for next-generation displays due to their high color purity, photoluminescence efficiency, and power efficiency. In this work, we present a simple and cost-effective method for fabricating flexible single- and multiple-layer films, and they can be detached and attached to the outside of OLEDs as a light-scattering and color-conversion layer. Light extraction efficiency is enhanced by forming low-density structures by using the reactive ion etching (RIE) process. As a result, the QD/PDMS composite film allowed for color conversion and achieved an excellent light extraction efficiency of up to 9.2%. Furthermore, the QD/PDMS composite film and greenish-blue OLED produced white light (CIEx,y = 0.28, 0.41), demonstrating the potential for application in broad areas, from flexible displays to lighting. The method provides a simple and cost-effective alternative to conventional processes.