Владислав Канакин

Prof. Владислав Канакин

Institute of Engineering Science, Yekaterinburg, Sverdlovskaya Oblast’, Russia
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 November 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Alexander SmirnovAlexander Smirnov
Alexander Smirnov
ESEvgeniya Smirnova
Evgeniya Smirnova
AKAnatoly Konovalov
Anatoly Konovalov
ВКВладислав Канакин
Владислав Канакин
The paper shows the applicability of data on the evolution of the elastic modulus measured by the instrumented microindentation technique to the determination of accumulated damage in metal matrix composites (MMCs) under high temperature deformation. A composite with a V95 aluminum alloy matrix (the Russian equivalent of the 7075 alloy) and SiC reinforcing particles is used as the research material. The metal matrix composite was produced by powder technology. The obtained results show that, under macroscopic compression at temperatures ranging between 300 and 500 °C, the V95\10% SiC MMC has the best plasticity at 300 °C. At a deformation temperature of 500 °C, the plastic properties are significantly lower than those at 300 and 400 °C.

10 January 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Alexander SmirnovAlexander Smirnov
Alexander Smirnov
ВКВладислав Канакин
Владислав Канакин
AKAnatoly Konovalov
Anatoly Konovalov
The paper investigates the rheological behavior and microstructuring of an AlMg6/10% SiC metal matrix composite (MMC). The rheological behavior and microstructuring of the AlMg6/10% SiC composite is studied for strain rates ranging between 0.1 and 4 s−1 and temperatures ranging from 300 to 500 °C. The microstructure formation is studied using EBSD analysis, as well as finite element simulation and neural network models. The paper proposes a new method of adding data to a training sample, which allows neural networks to correctly predict the behavior of microstructure parameters, such as the average grain diameter, and the fraction and density of low-angle boundaries with scanty initial experimental data. The use of neural networks has made it possible to relate the thermomechanical parameters of deformation to the microstructure parameters formed under these conditions. These dependences allow us to establish that, at strain rates ranging from 0.1 to 4 s−1 and temperatures between 300 to 500 °C, the main softening processes in the AlMg6/10% SiC MMC are dynamic recovery and continuous dynamic recrystallization accompanied, under certain strain and strain rate conditions at 300 and 350 °C, by geometric recrystallization.

1 December 2020 in Diagnostics, Resource and Mechanics of materials and structures
Verified
Journal Article
Closed access
Alexander SmirnovAlexander Smirnov
Alexander Smirnov
AKA. V. Konovalov
A. V. Konovalov
ВКВладислав Канакин
Владислав Канакин
The paper deals with a neural network to model the flow stress of the AlMg6 alloy at temperatures ranging between 300 and 500 C and strain rates from 1 to 25 s−1. In this temperature–strain-rate range, the movement of free dislocations is blocked and dynamic relaxation processes are inhibited. The results of training the neural network and its verification at a temperature not used in the training show that neural networks with a single hidden layer can correctly approximate and predict the rheological behavior of the AlMg6 alloy for the studied temperature–strain-rate range of deformation.

23 January 2025 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
Alexander SmirnovAlexander Smirnov
Alexander Smirnov
ESEvgeniya Smirnova
Evgeniya Smirnova
Dmitry VichuzhaninDmitry Vichuzhanin
Dmitry Vichuzhanin
YKYulia Khudorozhkova
Yulia Khudorozhkova
ISIrina Spirina
Irina Spirina
OMOlga Muizemnek
Olga Muizemnek
The aim of this paper is to describe a methodology for determining the elastic constants and thickness of the interphase between matrix and fiber in fiberglass plastic composites from macro- and micromechanical testing. Macromechanical testing is tension of unidirectional fiberglass plastics along and across the fiber direction. Micromechanical testing is tension of glass fibers and instrumented microindentation into the matrix and the fiberglass. The interphase thickness is determined by dynamic force microscopy on thin sections without a height difference. The measured interphase thickness is 621 nm. Based on the interphase thickness, a mesomechanical finite element model of a fiberglass monolayer is constructed. As a result, it is found that the elastic modulus and Poisson’s ratio are 12.7 GPa, 0.07. It is established that the elastic properties of the interphase differ significantly from those of the matrix. The paper also explores the possibility of determining the interphase thickness through computational experiments. It turns out that by knowing the actual elastic properties of the matrix and the fiber, as well as the fiberglass monolayer, it is feasible to calculate the interphase and its elastic properties with acceptable engineering accuracy. The deviation of the calculated interphase thickness from the experimentally measured one is 6%.