Ni/60WC coatings on copper substrate were placed via laser deposition (LD). A structural study was conducted using electron microscopy and a microhardness evaluation. Two body abrasive wear tests were conducted with a pin-on-plate reciprocating technique. A tool steel X12MF GOST 5960 (C-Cr-Mo-V 1.6-12-0.5-0.2) with a hardness of 63 HRC was used as a counterpart. The following results were obtained: Precipitation of the secondary carbides takes place in the thicker layers. Their hardness is lower than that of the primary carbides in the deposition (2425 HV vs. 2757 HV) because they mix with the matrix material. In the thin layers, precipitation is restricted due to a higher cooling rate. For both LD coatings, the carbide’s hardness increases compared to the initial mono-tungsten carbide (WC)-containing powder (2756 HV vs. 2200 HV). Such a high level of microhardness reflects the combined influence of a low level of thermal destruction of carbides during laser deposition and the formation of a boride-strengthening phase from the matrix powder. The thicker layer showed a higher wear resistance; weight loss was 20% lower. The changes in the thickness of the laser deposited Ni-WC coating altered its structure and wear resistance.
4 January 2011 in Metal Science and Heat Treatment
The study of the applicability of magnetic and optical methods to the detection of prefracture zones under fatigue degradation of structural materials is exemplified by the 09G2S steel. The regularities of changes in the signal of an attached fluxgate gradiometer with the increasing number of loading cycles have been revealed; namely, significant changes in the gradiometer readings on individual specimen surface areas prove to result from the formation of fracture zones. The change in the value of the coefficient of correlation among the speckle images is studied at different stages of cyclic testing. Speckle image heterogeneity is shown to appear due to fracture nucleation. Thus, the applicability of magnetic and speckle-interferometric methods to detecting prefracture zones in objects under cyclic loading is substantiated.
The aim of this paper is to describe a methodology for determining the elastic constants and thickness of the interphase between matrix and fiber in fiberglass plastic composites from macro- and micromechanical testing. Macromechanical testing is tension of unidirectional fiberglass plastics along and across the fiber direction. Micromechanical testing is tension of glass fibers and instrumented microindentation into the matrix and the fiberglass. The interphase thickness is determined by dynamic force microscopy on thin sections without a height difference. The measured interphase thickness is 621 nm. Based on the interphase thickness, a mesomechanical finite element model of a fiberglass monolayer is constructed. As a result, it is found that the elastic modulus and Poisson’s ratio are 12.7 GPa, 0.07. It is established that the elastic properties of the interphase differ significantly from those of the matrix. The paper also explores the possibility of determining the interphase thickness through computational experiments. It turns out that by knowing the actual elastic properties of the matrix and the fiber, as well as the fiberglass monolayer, it is feasible to calculate the interphase and its elastic properties with acceptable engineering accuracy. The deviation of the calculated interphase thickness from the experimentally measured one is 6%.
This paper deals with solving the problem of constructing two-level computational models relating the stress-strain state at the microscale to the stress-strain state of the structural component at the macroscale for layered polymer composite materials with unidirectional fiber stacking in a monolayer. The paper presents a two-level computational mechanical model of a ten-layer cross-ply fiberglass-reinforced polymer composite with (0/90) laying patterns. The model is based on microindentation data. The model is constructed using the finite element method. The constructed model has allowed us to predict the elastic properties of the composite and to calculate stresses at the microscale and macroscale levels of a specimen prior to fracture under tensile conditions. The elastic properties of the polymer composite material predicted by the computational model are compared with the properties obtained from real experiments. Calculated for fiberglass, the elasticity modulus and Poisson’s ratio are 31 GPa and 0.11, respectively. Similar elastic properties obtained from real experiments are 28 GPa and 0.10. The technique used in the paper can be applied to computational experiments with an actual structural component made of a multilayer polymer composite in order to determine the stress-strain state at the micro- and macroscale under external mechanical impact on the structure.