In this report, ternary titanium dioxide (TiO2)/carbon nanotubes (CNTs)/reduced graphene oxide (rGO) composites were fabricated by a facile and environmentally friendly one-pot solvethermal method for the removal of Rhodamine B (RhB). Its structures were represented by X-ray powder diffraction (XRD), Raman spectrometry, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The photocatalytic performance was tested by the degradation efficiency of RhB under UV-vis light irradiation. The experimental results indicated that photocatalytic activity improved as the ratio of CNTs:TiO2 ranged from 0.5% to 3% but reduced when the content increased to 5% and 10%, and the TiO2/CNTs/rGO-3% composites showed superior photocatalytic activity compared with the binary ones (i.e., TiO2/CNTs, TiO2/rGO) and pristine TiO2. The rate constant k of the pseudo first-order reaction was about 1.5 times that of TiO2. The improved photocatalytic activity can be attributed to the addition of rGO and CNTs, which reduced the recombination of photo-induced electron-hole pairs, and the fact that CNTs and rGO, with a high specific surface area and high adsorption ability to efficiently adsorb O2, H2O and organics, can increase the hydroxyl content of the photocatalyst surface.
Novel carbon nanotubes (CNTs)/titanium dioxide (TiO2)/zinc oxide (ZnO) composites have been successfully synthesized via a two-step solution method using titanyl sulfate as the titanium precursor. Its structural performances were researched by various characterization methods, such as X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and UV-vis diffuse reflectance spectroscopy (UV-vis DRS). The performance of the composites was tested by degrading rhodamine B (RhB) under UV-vis illumination and found to strongly rely on the content of ZnO. The experimental results showed that the CNT/TiO2/ZnO-90 wt % expressed more outstanding photocatalytic performance compared to the corresponding binary composites and the CNT/TiO2/ZnO-85 wt %, CNT/TiO2/ZnO-95 wt % materials. The improved photocatalytic activity was attributed to synergistic effect of CNT, TiO2 and ZnO, in which ZnO can absorb photons to produce electrons and holes, whereas TiO2 and CNT can reduce the electron-hole recombination.
An aggregation-caused quenching (ACQ)-active polymer (PF), an aggregation-induced emission (AIE)-active polymer (PFTPE) and an aggregation-enhanced emission (AEE)-active polymer (PTTPE) were synthesized by tetraphenylethane (TPE), fluorene and thiophene moieties. Polyurethane (PU) foams modified by PF, PFTPE and PTTPE, namely PU-PF, PU-PFTPE and PU-PTTPE, using ultrasonication-assisted method have been prepared. A comparative study of PU-PF, PU-PFTPE and PU-PTTPE for detection explosives had been performed, and significant fluorescence quenching was observed with the introduction of PA solutions. The as-prepared PU-PF, PU-PFTPE and PU-PTTPE sensors exhibited a superior sensitivity for PA solutions with different concentrations. Remarkably, PU-PF gave a quenching efficiency of 96.2%, higher than 93.5% for PU-PFTPE and 86.7% for PU-PTTPE at a PA concentration of 180 µg·mL−1 in methanol, which was attributed to the effective energy transfer from the fluorophore (PF) to the nitro explosive (PA). This suggested that some ACQ polymers, applied to detect explosives, could afford better performances than AIE or AEE polymers through modification of structures and selection of adequate carriers. At the same time, these chemical sensors can be recycled many times.
A series of “ravine-like” boron carbonitrides (abbreviation: BCN) were synthesized by a green precursor pyrolysis method at different temperatures (about 700–1100 °C). The highest electrochemical performance of BCN-800 (Named BCN-temperature) electrode was observed, because the “ravine-like” structure can significantly increase the contact area and improve the wettability between electrode and electrolyte. The BCN electrode exhibited ultrahigh specific capacitance 805.9 F/g (at a current density of 0.2 A/g), excellent rate capability, and good cycling stability (91%) after 3000 cycles at a current density of 8 A/g, showing high potential applications in supercapacitors.