This paper proposes an asymmetric hybrid tri-stable piezoelectric energy harvester for rotational motion (RHTPEH). The device features an asymmetric tri-stable piezoelectric cantilever beam positioned at the edge of a rotating disk. This beam is uniquely configured with an asymmetric arrangement of magnets. Additionally, an elastic amplifier composed of a vertical and a rotating spring connects the beam’s fixed end and the disk. This setup enhances both the rotational amplitude and vertical displacement of the beam during motion. A comprehensive dynamical model of the RHTPEH was developed using Lagrange’s equations. This model facilitated an in-depth analysis of the system’s behavior under various conditions, focusing on the influence of key parameters such as the asymmetry in the potential well, the stiffness ratio of the amplifier springs, the radius of the disk, and the disk’s rotational speed on the nonlinear dynamic response of the system. The results show that the asymmetric hybrid tri-stable piezoelectric energy harvester makes it easier to harvest the vibration energy in rotational motion and has excellent power output performance compared with the symmetric tri-stable piezoelectric energy harvester. The output power magnitude of the system at higher rotational speeds increases as the radius of rotation expands, but when the rotational speed is low, the steady-state output power magnitude of the system is not sensitive to changes in the radius of rotation. Theoretical analysis and numerical simulations validate the effectiveness of the proposed asymmetric RHTPEH for energy harvesting in low-frequency rotating environments.
The configuration of beam–column joints in precast concrete (PC) building structures varies widely, and different connection methods significantly affect the progressive collapse resistance of the structure. This study investigates the progressive collapse resistance of an innovative beam–column connection node frame. Finite element models of four-story, two-span space frame structures made of reinforced concrete (RC) and PC were developed using ANSYS 14.0/LS-DYNA R5.x software, employing nonlinear dynamic and static analysis to examine structural collapse behavior under bottom middle or corner column damage. Numerical results indicate that following the failure of the middle or corner column due to explosion loading, the vertical displacement and collapse rate of the PC structure with the novel connection method are less than those of the RC structure during collapse progression. Furthermore, upon removal of the middle or corner column, the residual load-carrying capacity of the PC structure with the innovative connection increased by 7% and 3.7%, respectively, compared to the RC structure. This suggests that PC structures with this type of connection demonstrate superior performance in resisting progressive collapse, offering valuable insights for future engineering applications.
Piezoelectric energy harvesting faces a primary challenge in effectively capturing low-orbit vibration energy across a broad frequency range. In this paper, we present a tri-stable piezoelectric energy harvester that incorporates a dynamic amplifier (TPEH + DM), specifically designed for efficient collection of low-orbit vibration energy. The TPEH + DM comprises a piezoelectric cantilever beam connected to an innovative dynamic amplifier at its restrained end, which enhances both the rotational and lateral displacement of the piezoelectric cantilever beam simultaneously. The governing coupled differential equations of motion for the system is derived based on the Lagrange equation, and analytical expressions for its steady-state response are obtained using the multi-scale method. The influence of factors such as the mass and the stiffness ratio of the dynamic amplifier on the steady-state dynamic output characteristics of the system is investigated using the theoretical analysis and numerical simulation. The results indicate that TPEH + DM exhibits significantly improved energy harvesting performance compared to TPEH under low-orbit external excitations. The bandwidth of inter-well motion and the TPEH + DM power output may be further increased by suitably modifying the relative stiffness between the cantilever beam and the dynamic amplifier. In addition, we analyze the time-domain behavior of the system’s output voltage using the ode45 solver under various external excitation frequencies and intensities. The results demonstrate that with appropriate adjustments to the mass of the tip magnet and the stiffness ratio of the dynamic amplifier, the proposed TPEH + DM system can harvest energy efficiently across a broad frequency range, even under low-orbit excitations.
The use of copper slag instead of part of the slag to prepare alkali-activated cementitious materials can achieve the resource utilisation of copper slag, but alkali-activated copper slag–slag composite cementitious materials have the disadvantages of high shrinkage and low flexural strength, which limit their application in practical engineering. In order to improve its performance, this study used glass fiber, polypropylene fiber, steel fiber at 0.2%, 0.4%, 0.6%, 0.8%, 1.0% by volume admixture into alkali-activated copper slag–slag composite cementitious materials, respectively, to explore the effect of fiber on the drying shrinkage and mechanical properties of alkali-activated copper slag–slag composite cementitious materials. The test results show that the addition of fibers can compensate the drying shrinkage of AAMs and improve their mechanical properties. 1.0% of GF and SF can compensate the drying shrinkage of 17.5% and 27.3%, and PPF can also inhibit the drying shrinkage of the material, but the drying shrinkage will be exacerbated when the dosage is more than 0.8%. The addition of fibers does not have a significant effect on the compressive strength, but significantly improves the flexural strength of the material. When the dosage of GF, PPF and SF reaches 0.6%, 0.8% and 1.0% respectively, the flexural strength of the specimen at 28d is increased by 7.9%, 19.86% and 61.66% compared with that of the blank control group, respectively. Through microstructural analysis, it was found that the fibers formed a mesh structure in the material, which effectively inhibited the development of cracks and improved the toughness of the material. This study provides a theoretical basis and practical guidance for the optimization of the properties of alkali-activated copper slag–slag composite cementitious materials.
11 October 2025 in Journal of Building Engineering