31 July 2024 in Facta Universitatis, Series: Mechanical Engineering
The paper presents an improved hybrid tri-stable cantilever piezoelectric energy harvester based on rotational motion, thus providing a new perspective for achieving higher efficiency in energy capture for rotational motion. The proposed system comprises a piezoelectric cantilever beam with an innovative dynamic amplifier installed at the edge of a vehicle's wheel hub. Through theoretical analysis and numerical simulations, the influence of parameters such as the mass of the tip magnetic on the piezoelectric beam, the wheel hub radius, rotational speed, and the ratio of the dynamic amplifier's spring stiffness are investigated with respect to the system's steady-state dynamic response and time-domain performance. A comparative analysis is also conducted with traditional tri-stable piezoelectric energy harvesters. The results demonstrate that the hybrid tri-stable piezoelectric energy harvester exhibits superior performance in capturing vibrational energy during rotational motion, compared to traditional tri-stable piezoelectric energy harvesters. Proper adjustments to the mass of the tip magnetic and the internal spring stiffness of the dynamic amplifier can enhance the system's output voltage and the rotational speed range of inter-well motion. Additionally, the rotational speed range of inter-well motion increases with the expansion of the wheel hub radius. However, when the rotational speed is below 100 rpm, the influence of varying the wheel hub radius on the system's output voltage is minimal.
1 April 2024 in AIP Advances
Piezoelectric energy harvesting faces a primary challenge in effectively capturing low-orbit vibration energy across a broad frequency range. In this paper, we present a tri-stable piezoelectric energy harvester that incorporates a dynamic amplifier (TPEH + DM), specifically designed for efficient collection of low-orbit vibration energy. The TPEH + DM comprises a piezoelectric cantilever beam connected to an innovative dynamic amplifier at its restrained end, which enhances both the rotational and lateral displacement of the piezoelectric cantilever beam simultaneously. The governing coupled differential equations of motion for the system is derived based on the Lagrange equation, and analytical expressions for its steady-state response are obtained using the multi-scale method. The influence of factors such as the mass and the stiffness ratio of the dynamic amplifier on the steady-state dynamic output characteristics of the system is investigated using the theoretical analysis and numerical simulation. The results indicate that TPEH + DM exhibits significantly improved energy harvesting performance compared to TPEH under low-orbit external excitations. The bandwidth of inter-well motion and the TPEH + DM power output may be further increased by suitably modifying the relative stiffness between the cantilever beam and the dynamic amplifier. In addition, we analyze the time-domain behavior of the system’s output voltage using the ode45 solver under various external excitation frequencies and intensities. The results demonstrate that with appropriate adjustments to the mass of the tip magnet and the stiffness ratio of the dynamic amplifier, the proposed TPEH + DM system can harvest energy efficiently across a broad frequency range, even under low-orbit excitations.
17 October 2024 in International Journal of Structural Stability and Dynamics
16 September 2026 in International Journal of Applied Mechanics
1 May 2025 in AIP Advances
This paper presents a rotational piezoelectric energy harvester (RPVEH) based on the Timoshenko beam model. The system comprises a five-layer composite cantilever beam with a tip magnet and two external magnets, creating a tri-stable potential energy function curve during vibration. The dynamic response expression of the system is derived using the generalized Hamilton’s principle, and the output power of the RPVEH is analyzed based on the harmonic balance method. The differences between the Timoshenko beam and the Euler beam models for various composite cantilever beam thicknesses are examined. Both sweep frequency and analytical results indicate that, under the same total beam thickness, the five-layer composite cantilever beam (0 < rs ≤ 0.8) captures more rotational energy over a wider speed range than the traditional three-layer composite cantilever beam (rs = 0). At a constant beam thickness (hb = 0.45 mm), as the beam length l increases, the peak power output of the five-layer composite cantilever beam is significantly improved compared to the traditional three-layer composite cantilever beam configuration: by 76%, 52%, and 19%, respectively (0.248 vs 0.141 W; 0.276 vs 0.181 W; 0.281 vs 0.237 W), accompanied by a 76% increase in power density for the 65 mm beam length. In addition, energy harvesting efficiency of the system under different substrate layer materials and thickness configurations is analyzed. It is found that using a cobalt alloy as the metal layer, which has a similar density and elastic modulus to the piezoelectric layer, significantly enhances the energy harvesting efficiency of the system.