This paper provides experimental data on the effective use of a new lubricating composition, which includes industrial oil of any brand with the addition of a nanometal of the component of a friction pair, which has a lower hardness. It is shown that this composition significantly reduces the wear resistance of the rails and wheels of rolling stock during operation, prevents electrochemical corrosion of the friction pair wheel–rail and, most importantly, stabilizes the coefficient of friction at the optimum level after a relatively short operating time. The experiments were performed on the friction pair, “sample of the bandage material of the railway wheel—a sample of the rail material”, with a ratio of hardness of the bandage material (Rockwell hardness, HRC scale—35.3) to the hardness of the rail material of 1.1. Test results show that in the case of industrial lubricant, the BioRail brand, with the addition of a nanomaterial friction pair with lower wear hardness of the rail metal sample, after three hours in operation the wear was practically not observed. Moreover, the average value of the friction coefficient for three hours of operation was maintained at the level 0.25, which is optimal for the friction pair wheel–rail. Similar experiments using only the same lubricant brand showed much worse results.
20 December 2019 in Eastern-European Journal of Enterprise Technologies
The authors have previously proposed and tested a method for increasing the wear resistance of heavy-loaded friction pairs by saturating industrial lubricants with the metallic nanopowder of the friction pair’s component that has a lower hardness. To confirm the effectiveness of this concept, this paper presents the results of experimental investigations into the tribological characteristics of two medium carbon steels (rail steel K74 and structural steel 20) during sliding friction. Friction surfaces lubricated with compositions based on the Bio Rail industrial lubricant were saturated with nanopowder additives of copper, carbon, and magnesium alloy, as well as K74 and 20 steels. The research findings indicate that lubricants saturated with nanomaterials of K74 and 20 steels help achieve the highest wear resistance, as compared to lubricants based on pure grease and lubricating compositions based on copper, magnesium alloy and carbon powders. The test results confirmed that the mean friction coefficient of the rail steel remained at the level of 0.25 for three hours of operation, which is optimal for the “wheel–rail” friction pair. The proposed method of manufacturing lubricating compositions can be used to improve the efficiency of lubrication of railway rails and rolling stock wheels.
МОНОГРАФІЯ Монографія є ще однією спробою визначити шляхи розвитку швидкісного пасажирського сполучення на українських залізницях. Проаналізовано декілька типових концепцій організації високошвидкісного руху на залізницях світу. Основними концепціями є: концепція відокремленої спеціальної системи високошвидкісного руху за прикладом Японії та Іспанії та концепція сумісного використання колій для швидкісного та вантажного руху за прикладом Німеччини, Італії, Польщі. Показано переваги та недоліки кожної з концепцій. Визначено закономірності деградаційних процесів у рейковій колії при експлуатації на лініях швидкісного руху вантажного рухомого складу з нормативними і наднормативними відхиленнями технічного стану. Досліджено вплив відхилень геометричних параметрів ходової частини вантажних вагонів на стан колії. Визначено деякі вимоги до конструкції колій, призначених для швидкісного пасажирського руху, суміщеного з вантажним. The monograph is another attempt to identify ways to develop high-speed passenger services on Ukrainian railways. Several typical concepts of the organization of high-speed traffic on the world's railways are analyzed. The main concepts are: the concept of a separate special system of high-speed traffic on the example of Japan and Spain and the concept of joint use of tracks for high-speed and freight traffic on the example of Germany, Italy and Poland. The advantages and disadvantages of each of the concepts are shown. The regularities of degradation processes in the rail track during operation on the lines of high-speed movement of freight rolling stock with normative and excessive deviations of the technical condition are determined. The influence of deviations of geometrical parameters of running gear of freight cars on track condition is investigated. Some requirements for the design of tracks designed for high-speed passenger traf-fic combined with freight are defined. ══════════════════════════════════ РЕЦЕНЗЕНТИ МОНОГРАФІЇ:Горобченко О.М. - д-р техн. наук, професор, декан факультету інфраструктури та рухомого складу залізниць Державного університету інфраструктури та технологій.Дьомін Р.Ю. - д-р техн. наук, в.о. генерального директора Дніпровського тепловозо-ремонтного заводу.Кара С.В. - канд. техн. наук, Начальник управління інжинірингу Науково-впроваджувального центру, Філії «Науково-дослідний та конструкторсько-технологічний інститут залізничного транспорту» АТ «Укрзалізниця». ══════════════════════════════════ ЗМІСТ: ВСТУП 1. СУЧАСНИЙ СТАН ТА КОНЦЕПЦІЇ ОРГАНІЗАЦІЇ ШВИДКІСНОГО ТА ВИСОКОШВИДКІСНОГО РУХУ ПОЇЗДІВ НА ЗАЛІЗНИЦЯХ СВІТУ1.1. Сучасна мережа високошвидкісних залізниць світу1.2. Концепції організації високошвидкісної мережі на залізницях світу 1.2.1. Японсько-іспанська концепція 1.2.2. Французька концепція 1.2.3. Італійська і німецька концепції1.3. Розвиток швидкісного руху в Україні1.4. Аналіз статистичних даних і експлуатаційних показників швидкісного руху Укрзалізниці 2. ДЕГРАДАЦІЙНІ ПРОЦЕСИ В РЕЙКОВІЙ КОЛІЇ ПРИ ЗМІШАНОМУ РУСІ ШВИДКІСНИХ І ВАНТАЖНИХ ПОЇЗДІВ2.1. Організація змішаного руху швидкісних і вантажних поїздів на українській залізниці 2.1.1. Типові відхилення верхньої будови колії в процесі її деградації2.2. Колія для швидкісного пасажирського руху суміщеного з вантажним 2.2.1. Визначення і обґрунтування умов безпеки та комфорту руху швидкісного сполучення щодо граничних параметрів деградації колії2.3. Визначення впливу рухомого складу на деградаційні процеси у рейковій колії2.4. Поперечна стійкість рейко-шпальної решітки та рейкової колії при сучасних конструкціях рейкових скріплень 2.4.1. Розрахунки стійкості рейко-шпальної решітки проти бокового здвигу...
30 September 2023 in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
The article aims to study the multi-level segmentation process of images of arbitrary configuration and placement based on features of spatial connectivity. Existing image processing algorithms are analyzed, and their advantages and disadvantages are determined. A method of organizing the process of segmentation of multi-gradation halftone images is developed and an algorithm of actions according to the described method is given.
One of the tasks of ensuring the safe and sustainable operation of railway transport is to assess the life cycle of the railway track and its elements—in particular, rails. It is known that the main cause of their failure is the development of defects that arise as a result of contact of rails with the wheels of rolling stock—contact fatigue defects. Modern approaches to predicting the contact-fatigue endurance of railway rails and wheels of rolling stock are based on the use of the kinetic theory of damage. The basis of such predictions is the calculation of the stress–strain state of rails under the action of combinations of external force and temperature influences, which is associated with the need to solve spatial boundary value problems of contact interaction. The complexity of such problems necessitates the use of numerical methods, such as the finite element method in particular, for their solution. This paper considers the features of constructing calculation schemes for such problems. Attention is primarily paid to assessing the influence of some design parameters of the rail track and wheels on the magnitude and distribution of stresses in the contact zone. The results will be useful for understanding the physical processes of damage accumulation, the occurrence and development of defects in rails and wheels, as well as for developing methods for predicting the contact fatigue endurance of important elements of railway infrastructure.