24 October 2017 in Eastern-European Journal of Enterprise Technologies
Energy saving direction on railway transport is substantiated based on reducing the motion resistance related to directing the undercarriages by a rail track. This motion resistance is defined as the kinematic resistance to motion. We clarified the nature of motion resistance associated with directing the rolling stock by a rail track. This opens up certain prospects in terms of reducing the kinematic motion resistance through design parameters of the trucks and the track. The kinematic resistance to motion could become an additional criterion for the optimal choice of characteristics of mechanical part of the undercarriages. The same applies to the permissible deviations in parameters of the rolling stock and the track.We model steady motion of a semi-wagon’s truck in a circular curve at constant velocity under the action of contact track forces, tractive force from the locomotive, and the unsuppressed centrifugal or centripetal forces of inertia. The kinematic motion resistance is determined as the longitudinal force applied to the truck’s pivot in order to balance all external forces.The dependences were obtained of specific kinematic resistance to motion on the motion velocity, base of the truck, radius of the curve, clearances of the wheelset in a rail track, and elevation of the outer rail. In particular, we derived a value of the motion velocity at which the minimum of resistance is observed. As we established, this speed does not match the equilibrium velocity and is 15−20 % lower.The study showed the possibility to predict resistance related to directing the undercarriages by a rail track. This opens up the prospect for choosing rational parameters of undercarriage gear of the rolling stock from the point of view of motion resistance
29 December 2017 in Eastern-European Journal of Enterprise Technologies
The study highlights the necessity to specify the safety factor against derailing of the wheels of a railway rolling stock. The modeling of the wheels’ derailment was carried out on the basis of considering the complete pattern of frictional interaction with the rails of the approaching and running-off wheels of a wheel pair. The simulation included the following previously overlooked factors: the dependence of the vertical component of the frictional force in the flange contact of the approaching wheel on the angle of the wheel running onto the rail; the influence of the frictional force in the flange contact of the approaching wheel on the increase in the horizontal lateral load on the flange; and the influence of the frictional force in the contact of the running-off wheel on the increase in the lateral load on the flange of the approaching wheel. The study has specified the safety factor – the Nadal criterion – against the derailment of the wheels of a railway stock. Unlike in the traditional approach, the safety factor of the wheel steadiness against derailment is assessed taking the frame force, rather than the lateral load on the flange, as the main factor of safety. This approach to determining the stability criterion gives more reliable results, since the frame force is more accessible for experimental and theoretical analysis.The proposed safety factor against the derailment of a railway stock, for different values of the flange inclination angle and the friction coefficient, is 10–50 % lower than the classical Nadal stability criterion. This makes the proposed criterion more reliable in assessing the safety of a railway rolling stock derailment
31 August 2021 in Eastern-European Journal of Enterprise Technologies
The analysis of operating conditions of induction traction motors as part of traction electric drives of electric locomotives reported here has revealed that they are powered by autonomous voltage inverters with asymmetric non-sinusoidal voltage. It was established that the induction motor operation may be accompanied by defects caused by the asymmetrical modes of the motor stator. A model of the induction motor has been proposed that takes into consideration changes in the values of mutual inductance of phases and complete inductance of the magnetization circuit due to changes in the geometric dimensions of the winding caused by a certain defect. An algorithm that considers the saturation of the magnetic circuit of the electric motor has been proposed. This approach to modeling an induction motor is important because if one of the stator's windings is damaged, its geometry changes. This leads to a change in the mutual inductance of phases and the complete inductance of the magnetization circuit. Existing approaches to modeling an induction motor do not make it possible to fully take into consideration these changes. The result of modeling is the determined starting characteristics for an intact and damaged engine. The comparison of modeling results for an intact engine with specifications has shown that the error in determining the controlled parameters did not exceed 5 %. The modeling results for the damaged engine demonstrated that the nature of change in the controlled parameters did not contradict the results reported by other authors. The discrepancy in determining the degree of change in the controlled parameters did not exceed 10 %. That indicates a high reliability of the modeling results. The proposed model of an induction electric motor could be used to investigate electromagnetic processes occurring in an electric motor during its operation as part of the traction drive of electric locomotives
3 December 2021 in Electrical Engineering & Electromechanics
The aim of the work is to develop a mathematical model of the traction motor of the pulsating current of an electric locomotive taking into account the magnetic losses in the motor steel to determine the starting parameters depending on the voltage of the armature winding. Methodology. Mathematical modeling of electromagnetic processes in a traction motor of pulsating current is applied taking into account the nonlinear nature of the armature inductance, the inductance of the excitation winding and the nonlinear nature of the universal magnetic characteristic. The magnetic losses in the steel of the traction motor were taken into account by establishing the dependence of these losses on the frequency of reversal, the magnetic flux in the magnetic circuit of the motor and the geometric dimensions of the motor. Results. The mathematical model of calculation of starting parameters of the traction engine of the pulsating current of the traction drive of the electric locomotive of alternating current taking into account the equation of instantaneous value of losses in engine steel is developed. The dynamic characteristics of the traction motor with pulsating current are obtained. It allows to investigate starting parameters of the traction engine on the basis of the received mathematical model and to design elements of the traction drive of the electric locomotive according to the specification, to choose optimum design parameters. Originality. For the first time a comprehensive study of the pulsating current traction motor was carried out taking into account the nonlinear nature of the armature inductance, excitation winding inductance and nonlinear nature of the universal magnetic characteristic and taking into account the magnetic losses in the motor steel. Practical significance. The model of the traction motor of pulsating current taking into account losses in steel of the engine on the basis of the carried-out calculation is developed. Experimental studies have confirmed the adequacy of the model, which allows to apply the obtained model to develop a mathematical model of an AC electric locomotive to study the electrodynamic processes in it at different modes of operation of the electric locomotive.
21 November 2018 in MATEC Web of Conferences
The aim of the work is to reduce the train rolling resistance to movement the railway vehicles. The article proves the expediency of changing the constructive scheme of railway vehicle wheel, which allows independent rotation their wheel mounting surface rolling and the guide surface (flange). There has been carried out the classification and analysis of the advantages and disadvantages of various structural schemes wheels of the railway vehicles. There has been analyzed the Features resistance to movement wheels of traditional and perspective constructive scheme. The obtained results allow drawing a conclusion about the possibility of a significant reduction in train rolling resistance to movement of railway vehicles with wheels perspective constructive scheme.