Among many types of batteries, Li-ion and Li-S batteries have been of great interest because of their high energy density, low self-discharge, and non-memory effect, among other aspects. Emerging applications require batteries with higher performance factors, such as capacity and cycling life, which have motivated many research efforts on constructing high-performance anode and cathode materials. Herein, recent research about cathode materials are particularly focused on. Low electron and ion conductivities and poor electrode stability remain great challenges. Three-dimensional (3D) porous nanostructures commonly exhibit unique properties, such as good Li⁺ ion diffusion, short electron transfer pathway, robust mechanical strength, and sufficient space for volume change accommodation during charge/discharge, which make them promising for high-performance cathodes in batteries. A comprehensive summary about some cutting-edge investigations of Li-ion and Li-S battery cathodes is presented. As demonstrative examples, LiCoO₂, LiMn₂O₄, LiFePO₄, V₂O₅, and LiNi_1−x−yCo_xMn_yO₂ in pristine and modified forms with a 3D porous structure for Li-ion batteries are introduced, with a particular focus on their preparation methods. Additionally, S loaded on 3D scaffolds for Li-S batteries is discussed. In addition, the main challenges and potential directions for next generation cathodes have been indicated, which would be beneficial to researchers and engineers developing high-performance electrodes for advanced secondary batteries.

In this report, eco-friendly and low-cost pyrite tailings are utilized as denitrification materials, while pyrite and magnetite are used as the control experimental groups to explore the denitrification performance of pyrite tailings. The results show that the removal effect of pyrite tailings on NO₃⁻ is slightly lower than that of pyrite. However, the concentration of NH₄⁺ decreased, and the effluent SO₄^2- concentration was lower than that of pyrite. In addition, pyrite with different particle sizes is prepared by the ball milling method, and the effect of particle size on the denitrification performance of pyrite is studied. The results show that with the decrease in particle size, microorganisms are more likely to use S in tailings as electron donors, the denitrification rate is faster, and the denitrification effect was better at the same time.

A CdS/SnS nanocomposite was prepared using a simple hydrothermal method and used as a sensitive material for the detection of carbon disulfide (CS₂) based on cataluminescence (CTL). The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive spectrometry (EDS) and X-ray photoelectron spectroscopy (XPS). The results show that the CdS/SnS nanocomposite sensor has a high sensitivity to CS₂ at a relatively low operating temperature (162 °C); the response time is about 3 s, and the recovery time is about 16 s. The modification of CdS effectively enhances the sensitivity of SnS sensors. The CTL intensity shows a good linear relationship at gas concentrations ranging from 6.75 to 168.75 ppm (R² = 09974), and the limit of detection (LOD) of CS₂ reached 0.96 ppm. In addition, the CdS/SnS sensor has excellent selectivity and good stability towards CS₂. The mechanism of the sensor is discussed in detail. This research shows that CdS/SnS has great potential for the detection of CS₂.

In this work, flower-like stannous sulfide (SnS) nanomaterials are synthesized using a hydrothermal method and used as sensitive materials for cataluminescence (CTL)-based detection of diethyl ether. Gas sensors based on SnS nanomaterials are prepared, and the SnS nanomaterials exhibit excellent gas-sensitive behavior towards ether. High sensitivity to ether is achieved at a relatively low operating temperature (153 °C) compared to other common sensors. The response time is 3 s and the recovery time is 8 s. The CTL intensity shows a good linear relationship (R² = 0.9931) with a detection limit of 0.15 ppm and the concentration of ether in the range of 1.5–60 ppm. The proposed CTL sensor shows good selectivity towards ether. In addition, a highly stable signal is obtained with a relative standard deviation of 1.5%. This study indicates that the SnS-based sensor has excellent gas-sensitive performance and shows potential for applications in the detection of ether.

To effectively carry out the bioremediation of a Pb²⁺ polluted environment, a lead-tolerant strain named D1 was screened from the activated sludge of a factory in Hefei, and its lead removal in a solution with Pb²⁺ concentration of 200 mg/L could reach 91% under optimal culture conditions. Morphological observation and 16S rRNA gene sequencing were used to identify D1 accurately, and its cultural characteristics and lead removal mechanism were also preliminarily studied. The results showed that the D1 strain was preliminarily identified as the Sphingobacterium mizutaii strain. The experiments conducted via orthogonal test showed that the optimal conditions for the growth of strain D1 were pH 7, inoculum volume 6%, 35 °C, and rotational speed 150 r/min. According to the results of scanning electron microscopy and energy spectrum analysis before and after the D1 exposure to lead, it is believed that the lead removal mechanism of D1 is surface adsorption. The Fourier transform infrared spectroscopy (FTIR) results revealed that multiple functional groups on the surface of the bacterial cells are involved in the Pb adsorption process. In conclusion, the D1 strain has excellent application prospects in the bioremediation of lead-contaminated environments.