Bogdan Roşca

Prof. Dr. Bogdan Roşca

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2018 in Procedia Manufacturing
Verified
Journal Article
Open access
CCCostin Andrei Cadere
Costin Andrei Cadere
MBMarinela Barbuta
Marinela Barbuta
BRBogdan Roşca
Bogdan Roşca
ASAdrian Alexandru Serbanoiu
Adrian Alexandru Serbanoiu
ABAndrei Burlacu
Andrei Burlacu
IOIrina Oancea
Irina Oancea

1 September 2017 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
MBM Barbuta
M Barbuta
ASAdrian Alexandru Serbanoiu
Adrian Alexandru Serbanoiu
RTR Teodorescu
R Teodorescu
BRBogdan Roşca
Bogdan Roşca
RMR Mitroi
R Mitroi
GBG Bejan
G Bejan
In the study are presented the experimental results obtained for polymer concrete prepared with epoxy resin, aggregates, fly ash as filler and two types of fibers: wool and hemp. The influence of type and dosage of fibers were studied. The density and mechanical characteristics were determined: compressive strength, flexural strength and split tensile strength. For both types of fibers, with increasing the fiber dosage the density decreases. The studied dosages had not an important influence on mechanical strengths. The fibers improved especially the tensile strength and the compressive strength presented generally smaller values than the control mix.

1 October 2012
Verified
Conference Paper
Closed access
BRBogdan Roşca
Bogdan Roşca
JKJ.T.B.A. Kessels
J.T.B.A. Kessels
HBH.J. Bergveld
H.J. Bergveld
PBP.P.J. van Den Bosch
P.P.J. van Den Bosch
This paper presents an on-line model identification method for Li-ion battery parameters that combines high accuracy and low computational complexity. Experimental results show that modeling errors are smaller than 1% throughout the feasible operating range. The identified model is used in a state observer - an Extended Kalman Filter (EKF) - to obtain an indication about the battery State of Charge (SoC). A novel method to estimate the actual battery capacity on-line, based on the data from the state observer is presented. Based on the real battery capacity, an indication about the State of Health (SoH) can be given. Simulation and experimental results are presented to validate the proposed methodology. Battery capacity estimation errors under 4% are achieved by using only 30 minutes of data (battery voltage and current measurements) acquired during normal driving.

29 March 2025 in Sustainability
Verified
Journal Article
Open access
PDF file
BRBogdan Roşca
Bogdan Roşca
The quantity of construction demolition waste (CDW) has been increasing due to the demolition of many old buildings throughout the world. So far, all the statistics indicate that there is a very large generation of CDW, which increases annually. The increasing amount CDW in landfills will cause a scarcity of landfill space and will also increase pollution and cost due to transportation. Recycled brick aggregate concrete (RBAC) incorporating polystyrene (EPS) aggregate beads has emerged as an alternative lightweight material with numerous obvious sustainable benefits, suitable for a future circular economy. The goal of this paper is to assess the feasibility of obtaining lightweight aggregate concrete of structural grade with recycled brick aggregate (RBA) as a coarse aggregate and the incorporation of polystyrene beads in a certain percentage by conducting an experimental study on the dry and apparent density, compressive strength, split-tensile strength and elasticity modulus. In addition, the effects of the w/c ratio and cement content on these properties were studied to provide useful information for the performance optimization of this concrete with RBA and polystyrene (EPS) beads. The properties were investigated for two cement contents, 400 and 360 kg/m3, and two ratios between water and cement, 0.43 and 0.39, respectively. The RBAC mixtures containing EPS beads in 15%, 25% and 35% replacement percentages were evaluated through a comprehensive test program based on the European standards. The results showed that, in general, the use of polystyrene (EPS) beads decreased the mechanical properties of the recycled brick aggregate concrete; however, the outcome indicates the potential for producing lightweight concrete of different grades, including structural classes. It was found that the developed lightweight concrete presents a uniform distribution of the polystyrene granules in the hardened volume of concrete. Also, it was found that the recycled brick aggregate with a 16 mm maximum size did not negatively influence the uniform distribution of the EPS beads, avoiding concentrations of beads. With the increase in the percentage of EPS beads, the properties of the recycled brick aggregate concrete were found to be less sensitive to the water-to-cement ratio.

15 April 2010 in Journal of Applied Sciences
Verified
Journal Article
Closed access
PMPetru Mihai
Petru Mihai
IHIoan Hirhui
Ioan Hirhui
BRBogdan Roşca
Bogdan Roşca

1 March 2010 in Journal of Applied Sciences
Verified
Journal Article
Closed access
PMP. Mihai
P. Mihai
IGI. Gosav
I. Gosav
BRBogdan Roşca
Bogdan Roşca