Dimples are small concavities imprinted on a flat surface, known to affect heat transfer and also flow separation and aerodynamic drag on bluff bodies when acting as a standard roughness. Recently, dimples have been proposed as a roughness pattern that is capable of reducing the turbulent drag of a flat plate by providing a reduction of skin friction that compensates the dimple-induced pressure drag and leads to a global benefit. The question whether dimples do actually work to reduce friction drag is still unsettled. In this paper, we provide a comprehensive review of the available information, touching upon the many parameters that characterize the problem. A number of reasons that contribute to explaining the contrasting literature information are discussed. We also provide guidelines for future studies by highlighting key methodological steps required for a meaningful comparison between a flat and dimpled surface in view of drag reduction.

Riblets are micro-grooves capable of decreasing skin-friction drag, but recent work suggests that additional benefits are possible for other components of aerodynamic drag. The effect of riblets on a fixed-wing, low-speed Unmanned Aerial Vehicle (UAV) on the total aerodynamic drag are assessed here for the first time by means of RANS simulations. Since the microscopic scale of riblets precludes their direct representation in the geometric model of the UAV, we model riblets via a homogenised boundary condition applied on the smooth wall. The boundary condition consists in a suitably tuned partial slip, which assumes riblets to be locally aligned with the flow velocity, and to possess optimal size. Several configurations of riblets coverage are considered to extract the potential for drag reduction of different parts of the aircraft surface. Installing riblets with optimal size over the complete surface of the UAV leads to a reduction of 3% for the drag coefficient of the aircraft. In addition to friction reduction, analysis shows a significant additional form of drag reduction localised on the wing. By installing riblets only on the upper surface of the wing, total drag reduction remains at 1.7%, with a surface coverage that is only 29%, thus yielding a significant improvement in the cost–benefit ratio.

The ability of streamwise-travelling waves of spanwise velocity to reduce the turbulent skin-friction drag is assessed in the compressible regime. Direct numerical simulations are carried out to compare drag reduction in subsonic, transonic and supersonic channel flows. Compressibility improves the benefits of the travelling waves, in a way that depends on the control parameters: drag reduction becomes larger than the incompressible one for small frequencies and wavenumbers. However, the improvement depends on the specific procedure employed for comparison. When the Mach number is varied and, at the same time, wall friction is changed by the control, the bulk temperature in the flow can either evolve freely in time until the aerodynamic heating balances the heat flux at the walls, or be constrained such that a fixed percentage of kinetic energy is transformed into thermal energy. Physical arguments suggest that, in the present context, the latter approach should be preferred. This provides a test condition in which the wall-normal temperature profile more realistically mimics that in an external flow, and also leads to a much better scaling of the results, over both the Mach number and the control parameters. Under this comparison, drag reduction is only marginally improved by compressibility.

We address the Reynolds number dependence of the turbulent skin-friction drag reduction induced by streamwise-travelling waves of spanwise wall oscillations. The study relies on direct numerical simulations of drag-reduced flows in a plane open channel at friction Reynolds numbers in the range $1000 \leqslant Re_\tau \leqslant 6000$ , which is the widest range considered so far in simulations with spanwise forcing. Our results corroborate the validity of the predictive model proposed by Gatti & Quadrio (J. Fluid Mech. vol. 802, 2016, pp. 553–558): regardless of the control parameters, the drag reduction decreases monotonically with $Re$ at a rate that depends on the drag reduction itself and on the skin-friction of the uncontrolled flow. We do not find evidence in support of the results of Marusic et al. (Nat. Commun. vol. 12, no. 1, 2021, pp. 5805), which instead report by experiments an increase of the drag reduction with $Re$ in turbulent boundary layers, for control parameters that target low-frequency, outer-scaled motions. Possible explanations for this discrepancy are provided, including obvious differences between open channel flows and boundary layers, and possible limitations of laboratory experiments.

Exact budget equations are derived for the coherent and stochastic contributions to the second-order structure function tensor. They extend the anisotropic generalised Kolmogorov equations (AGKE) by considering the coherent and stochastic parts of the Reynolds stress tensor, and are useful for the statistical description of turbulent flows with periodic or quasi-periodic features, like, for example, the alternate shedding after a bluff body. While the original AGKE describe production, transport, inter-component redistribution and dissipation of the Reynolds stresses in the combined space of scales and positions, the new equations, called AGKE.