Changes in the organic matrix of composite resins have been proposed to improve their surface properties. However, polishing systems may perform differently in different materials. This study compared the effect of polishing systems on the surface roughness of four composite resins containing different resin monomers: Admira Fusion (nanohybrid containing pure ormocer), Aura Bulkfill (nanohybrid containing Bis-GMA, UDMA), Charisma Diamond (nanohybrid containing TCD-DI-HEA) and Vittra APS (nanofilled containing UDMA). Cylinders (N = 120, n = 10) were prepared from each material and the top surface of each specimen was grounded using a diamond finishing bur. Baseline measurements of surface roughness (Ra) were recorded using a contact profilometer and the specimens of each composite were divided into three subgroups according to the polishing system: one-step, two-step, three-step. Ra measurements were recorded also after polishing. Data were analyzed using three-way ANOVA and Tukey’s test (p < 0.05). The baseline roughness of all composites was significantly reduced after polishing (p < 0.001). The two-step polishing system provided the smoothest surface for Admira Fusion (0.0770 ± 0.0171) and Charisma (0.1091 ± 0.0090), whereas for Aura and Vittra no significantly differences were found for the three polishing systems tested. The surface smoothness seems to be more material dependent than step dependent, but all tested systems provided clinically acceptable results.
Different agents have been proposed to prevent the progression of acid induced dental substance losses, which are called erosive tooth wear (ETW), such as fluorides, calcium, and phosphate-based products; however, there is a need for a further increase in efficacy. Recently, the ability of polymers to interact with the tooth surface, forming acid resistant films, has come into the focus of research; nevertheless, there is still the need for a better understanding of their mode of action. Thus, this article provides an overview of the chemical structure of polymers, their mode of action, as well as the effect of their incorporation into oral care products, acid beverages, and antacid formulations, targeting the prevention of ETW. Recent evidence indicates that this may be a promising approach, however, additional studies are needed to confirm their efficacy under more relevant clinical conditions that consider salivary parameters such as flow rate, composition, and clearance. The standardization of methodological procedures such as acid challenge, treatment duration, and combination with fluorides is necessary to allow further comparisons between studies. In conclusion, film-forming polymers may be a promising cost-effective approach to prevent and control erosive demineralization of the dental hard tissue.
Objective: Assessment of the influence of theultrasound and irrigant solutions on the bondstrength (BS) of glass fiber posts. Material andMethods: Sixty-six roots of bovine teeth standardizedat 16 mm were used. The roots were submitted to abiomechanical preparation up to size #80 Kerr file,with irrigation of 5ml of saline solution at everyfile change and then filled. The canals underwentpartial desobturation and were divided into 6 groupsaccording to the irrigant solution and the use ofultrasound prior to the post cementation: S – salinesolution; C – 2% chlorhexidine solution; H –2.5%sodium hypochlorite solution; US – saline solution+ ultrasound; UC – 2% chlorhexidine solution +ultrasound; UH – 2.5% sodium hypochlorite solution+ ultrasound. After the cementation of the posts, thespecimens were cut into 3 slices of 2 mm of thickness,perpendicular to its long axis. The samples weresubmitted to push-out test with crosshead speed of1 mm/min and load of 50kgf. The data obtainedwere submitted to ANOVA and Tukey test (level ofsignificance of 5%). Results: Groups C 7.77(±1.8)a,UC 7.82(±1.6)a, S 7.33(±2.2)a, US 6.16(±2.3)a, H5.43(±1.3)b, UH 5.01(±2.3)b values in Mpa. Onlythe irrigant solutions showed statistically significantdifferences (<0.05). Tukey test revealed smallerbond strength for the specimens treated with SodiumHypochlorite (b). Conclusions: The ultrasoundtreatment did not show significant differencecompared with the other groups; therefore, its usecan be indicated prior to the cementation of glassfiber posts without damage to the bond strength. Thesodium hypochlorite solution showed the smallest BSvalues compared with the other groups.