Grzegorz Stachyra

Mr. Grzegorz Stachyra


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 November 2023 in Materials
Verified
Journal Article
Open access
PDF file
GSGrzegorz Stachyra
Grzegorz Stachyra
KLKloda Lukasz
Kloda Lukasz
ZSZofia Szmit
Zofia Szmit
This study primarily focuses on conducting, both experimentally and numerically, a modal analysis of a cantilever composite beam. Through extended numerical simulations, we investigate Campbell diagrams, which, depending on the rotation speed of the structure, comprise natural frequencies and their corresponding modal shapes. Our results are categorized into two main aspects: the classical single-mode behavior and an innovative extension involving linearly coupled modal analysis. One key novelty of our research lies in the introduction of an analytical description for coupled mode shapes, which encompass various deformations, including bending, longitudinal deformations, and twisting. The most pronounced activation of dynamic couplings within the linear regime for a 45∘ preset angle is observed, though the same is not true of the 0∘ and 90∘ preset angles, for which these couplings are not visible. In addition to the modal analysis, our secondary goal is to assess the lift, drag forces, and moment characteristics of a rectangular profile in uniform flow. We provide insights into both the static and dynamic aerodynamic responses experienced by the beam within an operational frequency spectrum. This study contributes to a deeper understanding of the dynamics of composite rotating beams and their aerodynamic characteristics.

6 May 2022 in Materials
Verified
Journal Article
Open access
PDF file
ZSZofia Szmit
Zofia Szmit
KLKloda Lukasz
Kloda Lukasz
MKMarcin Kowalczuk
Marcin Kowalczuk
GSGrzegorz Stachyra
Grzegorz Stachyra
JWJerzy Warminski
Jerzy Warminski
The purpose of the current study is the experimental analysis of the dynamics and aerodynamic loads of a three-bladed rotor. The experimental tests focus on the rotation with three different angular velocities; for each angular speed, four different preset angles of beam have been studied. During the laboratory experiment, strain gauges, as well as high-speed cameras, have been used as the measurement system. The images from the high-speed cameras have been used to obtain aerodynamic loads in the form of polynomials, while the signals from strain gauges mounted on each beam allowed us to observe the synchronization phenomenon between beams.

21 October 2024 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
MŚMariusz Śniadkowski
Mariusz Śniadkowski
GSGrzegorz Stachyra
Grzegorz Stachyra
DWDorota Wójcicka-Migasiuk
Dorota Wójcicka-Migasiuk
Automation is a wide range of technologies that minimise human involvement in various home systems to improve the quality of life. Home automation systems are becoming more common and easier to build. It is possible to adapt them for remote control via the Internet or to connect them to a home...

23 March 2026 in Eksploatacja i Niezawodność – Maintenance and Reliability
Verified
Journal Article
Closed access
RNRadosław Nowak
Radosław Nowak
GSGrzegorz Stachyra
Grzegorz Stachyra
PPPaweł Pieńczuk
Paweł Pieńczuk
MGMichał Gmitrzuk
Michał Gmitrzuk
MŚMariusz Śniadkowski
Mariusz Śniadkowski
Helicopter pilots operate in a vibratory environment that substantially exceeds that of fixed-wing aircraft, creating stringent demands for the durability and dynamic stability of head-supported equipment. This study presents an experimental investigation of the vibration behaviour of prototype helicopter pilot goggles tested on an electrodynamic exciter over a frequency range exceeding applicable defence standards. The aim was to verify assembly integrity, assess the short-term strength of load-bearing components, identify natural frequencies of the goggle system, and generate reference data for future finite-element model. Acceleration and displacement responses were recorded using accelerometers and processed through custom software to obtain amplitude–frequency characteristics. The results indicate significant amplification of vibration in selected structural regions, eg. 50–250 Hz and 450–500 Hz, corresponding to natural modes of both the holder and the goggles. These findings confirm the sensitivity of the system to vibratory inputs comparable to those in helicopter cockpits