The mixtures of cations and anions used in hybrid halide perovskites for high-performance solar cells often undergo element and phase segregation, which limits device lifetime. We adapted Schelling’s model of segregation to study individual cation migration and found that the initial film inhomogeneity accelerates materials degradation. We fabricated perovskite films (FA 1–x Cs x PbI 3 ; where FA is formamidinium) through the addition of selenophene, which led to homogeneous cation distribution that retarded cation aggregation during materials processing and device operation. The resultant devices achieved enhanced efficiency and retained >91% of their initial efficiency after 3190 hours at the maximum power point under 1 sun illumination. We also observe prolonged operational lifetime in devices with initially homogeneous FACsPb(Br 0.13 I 0.87 ) 3 absorbers.
One of the primary challenges in commercializing perovskite solar cells (PSCs) is achieving both high power conversion efficiency (PCE) and sufficient stability. We integrate wafer-scale continuous monolayer MoS 2 buffers at the top and bottom of a perovskite layer through a transfer process. These films physically block ion migration of perovskite into carrier transport layers and chemically stabilize the formamidinium lead iodide phase through strong coordination interaction. Effective chemical passivation results from the formation of Pb-S bonds, and minority carriers are blocked through a type-I band alignment. Planar p-i-n PSCs (0.074 square centimeters) and modules (9.6 square centimeters) with MoS 2 /perovskite/MoS 2 configuration achieve PCEs up to 26.2% (certified steady-state PCE of 25.9%) and 22.8%, respectively. Moreover, the devices show excellent damp heat (85°C and 85% relative humidity) stability with <5% PCE loss after 1200 hours and notable high temperature (85°C) operational stability with <4% PCE loss after 1200 hours.
Perovskite solar cells (PSCs) are a promising and fast-growing type of photovoltaic cell due to their low cost and high conversion efficiency. The high efficiency of PSCs is closely related to the quality of the photosensitive layer, and the high-quality light absorbing layer depends on the growth condition of the crystals. In the formation of high-quality crystals, annealing is an indispensable and crucial part, which serves to evaporate the solvent and drive the crystallization of the film. Various annealing methods have different effects on the promotion of the film growth process owing to the way they work. Here, this review will present a discussion of the growth puzzles and quality of perovskite crystals under different driving forces, and then explain the relationship between the annealing driving force and crystal growth. We divided the main current annealing methods into physical and chemical annealing, which has never been summarized before. The main annealing methods currently reported for crystal growth are summarized to visualize the impact of annealing design strategies on photovoltaic performance, while the growth mechanisms of thin films under multiple annealing methods are also discussed. Finally, we suggest future perspectives and trends in the industrial fabrication of PSCs in the future. The review promises industrial manufacturing of annealed PSCs. The review is expected to facilitate the industrial fabrication of PSCs.
The passivation engineering of the hole transport layer in perovskite solar cells (PSCs) has significantly decreased carrier accumulation and open circuit voltage (Voc) loss, as well as energy band mismatching, thus achieving the goal of high-power conversion efficiency. However, most devices incorporating organic/inorganic buffer layers suffer from poor stability and low efficiency. In this article, we have proposed an inorganic buffer layer of Cu2O, which has achieved high efficiency on lower work function metals and various frequently used hole transport layers (HTLs). Once the Cu2O buffer layer was applied to modify the Cu/PTAA interface, the device exhibited a high Voc of 1.20 V, a high FF of 75.92%, and an enhanced PCE of 22.49% versus a Voc of 1.12 V, FF of 69.16%, and PCE of 18.99% from the (PTAA/Cu) n-i-p structure. Our simulation showed that the application of a Cu2O buffer layer improved the interfacial contact and energy alignment, promoting the carrier transportation and reducing the charge accumulation. Furthermore, we optimized the combinations of the thicknesses of the Cu2O, the absorber layer, and PTAA to obtain the best performance for Cu-based perovskite solar cells. Eventually, we explored the effect of the defect density between the HTL/absorber interface and the absorber/ETL interface on the device and recommended the appropriate reference defect density for experimental research. This work provides guidance for improving the experimental efficiency and reducing the cost of perovskite solar cells.