In the context of protecting the ecological environment and carbon neutrality, high-value recycling of flexible polyurethane foam (F-PUF) scraps, generated in the production process, is of great significance to save petroleum raw materials and reduce energy consumption. In the present study, F-PUF scraps were ground into powder by strong shear regrinding using two-roll mill and then reused as a partial replacement of polyol for re-foaming. A series of characterizations were employed to investigate the effect of milling cycles, roller temperatures, and content of the powder on the properties of the powder and F-PUF containing powder. It was revealed that the mechanochemical effect induced breaking of the cross-linking structure and increased activity of the powder. The volume mean diameter (VMD) of powder prepared with 7 milling cycles, at room temperature, is about 97.73 μm. The microstructure and density of the F-PUF containing powder prepared in the above-mentioned manner to replace up to 15 wt.% polyol, is similar to the original F-PUF, with resilience 49.08% and compression set 7.8%, which indicates that the recycling method will play an important role in industrial applications.

Carbon nanotube (CNT), as reinforcing agents in natural rubber (NR), has gained a large amount of consideration due to their excellent properties. Uniform dispersion of CNT is the key to obtaining high-performance NR nanocomposites. In this contribution, a novel ultrasonic grinding dispersion method of CNT with waterjet-produced rubber powder (WPRP) as a carrier is proposed. Microscopic morphologies show that a Xanthium-like structure with WPRP as the core and CNTs as the spikes is formed, which significantly improves the dispersion of CNT in the NR matrix and simultaneously strengthens the bonding of the WPRP and NR matrix. With the increase in the WPRP loading, the Payne effect of CNT/WPRP/NR composites decreases, indicating the effectiveness of the dispersion method. The vulcanization MH and ML value and crosslinking density increase with the increase in the WPRP loading, whereas the scorch time and cure time exhibit a decreasing trend when the WPRP loading is less than 15 phr. It is found that the CNT/WPRP/NR composites filled with 5 phr WPRP have a 4% increase in 300% modulus, a 3% increase in tensile strength, while a 5% decrease in Akron abrasion loss, compared to CNT/NR composites.

Common swelling agents used in the mechano-chemical rubber devulcanization process usually require high temperatures to achieve satisfactory swelling effects, which results in severe production of pollutants and reduces the selectivity of bond scissions. This work presents an environmentally friendly swelling agent, terpinene, which can swell the rubber crosslink structures at low temperatures. Both a rubber swelling experiment and a rubber reclaiming experiment with a mechano-chemical devulcanization method are conducted to explore the swelling effects of terpinene. After soaking in terpinene at 60 °C for 90 min, the length elongation of the rubber sample reaches 1.55, which is much higher than that in naphthenic oil and is comparable to that in toluene. When adding 3 phr of terpinene for every 100 phr of waste rubber during the reclaiming process, the bond scissions exhibit high selectivity. After revulcanization, the reclaimed rubbers have a tensile strength of 17 MPa and a breaking elongation of 400%. Consequently, the application of terpinene as the swelling agent in the LTMD method can greatly improve the properties of reclaimed rubbers, thereby enhancing the dual value for the economy and environment.

To reinforce natural rubber latex foam, fumed silica and precipitated silica are introduced into latex foam prepared using the Dunlop process as fillers. Four types of silica, including Aerosil 200 (hydrophilic fumed silica), Reolosil DM30, Aerosil R972 (hydrophobic fumed silica), and Sipernat 22S (precipitated silica), are investigated. The latex foam with added silica presents better mechanical and physical properties compared with the non-silica foam. The hydrophobic nature of the fumed silica has better dispersion in natural rubber compared to hydrophilic silica. The specific surface area of silica particles (BET) also significantly influences the properties of the latex foam, with larger specific surface areas resulting in better dispersity in the rubber matrix. It was observed that exceeding 2 phr led to difficulties in the foaming process (bulking). Furthermore, higher loading of silica also affected the rubber foam, resulting in an increased shrinkage percentage, hardness, compression set, and crosslink density. The crosslink density increased from 11.0 ± 0.2 mol/cm³ for non-silica rubber to 11.6 ± 0.6 mol/cm³ for Reolosil DM30. Reolosil DM30 also had the highest hardness, with a hardness value of 52.0 ± 2.1 IRHD, compared to 45.0 ± 1.3 IRHD for non-silica foam rubber and 48 ± 2.4 IRHD for hydrophilic fumed silica Aerosil 200. Hydrophobic fumed silica also had the highest ability to return to its original shape, with a recovery percentage of 88.0% ± 3.5% compared to the other fumed silica. Overall, hydrophobic fumed silica had better results than hydrophilic silica in both fumed and precipitated silica.