Fabrication of glass with complex geocd the low resolution of particle‐based or fused glass technologies. Herein, a high‐resolution 3D printing of transparent nanoporous glass is presented, by the combination of transparent photo‐curable sol–gel printing compositions and digital light processing (DLP) technology. Multi‐component glass, including binary (Al2O3‐SiO2), ternary (ZnO‐Al2O3‐SiO2, TiO2‐Al2O3‐SiO2), and quaternary oxide (CaO‐P2O5‐Al2O3‐SiO2) nanoporous glass objects with complex shapes, high spatial resolutions, and multi‐oxide chemical compositions are fabricated, by DLP printing and subsequent sintering process. The uniform nanopores of Al2O3‐SiO2‐based nanoporous glasses with the diameter (≈6.04 nm), which is much smaller than the visible light wavelength, result in high transmittance (>95%) at the visible range. The high surface area of printed glass objectives allows post‐functionalization via the adsorption of functional guest molecules. The photoluminescence and hydrophobic modification of 3D printed glass objectives are successfully demonstrated. This work extends the scope of 3D printing to transparent nanoporous glasses with complex geometry and facile functionalization, making them available for a wide range of applications.
The hydrophobicity and corrosion resistance of composite coatings can be effectively improved by changing the electrodeposition method and adding inorganic nanoparticles. In this work, the incorporation of WS2 nanoparticles significantly increased the surface roughness of Ni-Co coatings. The best hydrophobicity and corrosion resistance of the Ni-Co/WS2 nanocomposite coatings (water contact angle of 144.7°) were obtained in the direct current electrodeposition mode when the current density was 3 A/dm2 and the electrodeposition time was 50 min. Compared with direct current electrodeposition, the pulsed current electrodeposition method was more conducive to improving the electrodeposition performance of the nanocomposite coatings. Under the conditions of a current density of 3 A/dm2, pulse duty cycle of 70%, and pulse frequency of 1000 Hz, the nanocomposite coatings reached a superhydrophobic state (water contact angle of 153.8°). The nanocomposite coatings had a slower corrosion rate and larger impedance modulus in this state, and thus the corrosion resistance was superior. The wetting state of the Ni-Co/WS2 nanocomposite coating surface was closer to the Cassie–Baxter model. The protective air layer formed by the layered rough microstructures significantly reduced the actual contact area between the liquid and the substrate, achieving excellent hydrophobic and corrosion resistance properties.
7 September 2022 in Journal of Materials Chemistry C
We fabricate transparent fluoroindate glass-ceramics with phase-selective crystallization (SrF2, CaF2 and MgF2) using a general one-step strategy. The ab initio molecular dynamics provide fundamental insights into phase-separation at the atomic scale.
The uniformity and microstructure of the copper deposition in the high aspect ratio plated through holes (penetrating holes) are crucial for the performance of printed circuit board. We systematically investigated the effects of reverse pulse parameters in the period pulse reverse (PPR) plating on the uniformity and microstructure of the copper deposition, including reverse pulse frequency, reverse pulse duty cycle and reverse pulse current density. The Cu deposition behavior (throwing power) and its crystallographic characteristics, including grain size, crystallographic orientation, and grain boundary, were characterized by means of field-emission scanning electron microscopy (FE-SEM), X-ray diffractometer (XRD), and electron backscatter diffraction (EBSD). Our results clarify that the reverse pulse current density and duty ratio should be low to achieve the full filling and high uniformity of the through holes. The reverse pulse frequency of 1500 Hz would prevent the through holes to be fully filled. The copper electrodeposition in PTH prepared by double pulse electrodeposition has the good (111) surface texture and grain boundary distribution. This work demonstrated that the period pulse reverse (PPR) plating provides unique advantages in achieving the ultra-uniform copper deposition in the high aspect ratio plated through holes.
Laser propagation in a tandem structure comprising carbon nanotubes and phthalocyanines is studied by Z-scan method. Due to the different mechanisms of the two materials, the laser beam can be attenuated with different absorptivities, by changing the sequence of light passing through each material. Numerical simulations considering the effect of path length and the change of nonlinear coefficient within each material are conducted for understanding the distribution of laser intensity in the tandem system and hence, fitting of the asymmetric Z-scan curves. The results are helpful for the design of nonlinear optical devices comprising multiple nonlinear materials and mechanisms.