The paper is dedicated to the life prolongation of the tools designed for deep-hole drilling. Among available methods, an ion implantation process was used to improve the durability of tungsten carbide (WC)-Co guide pads. Nitrogen fluencies of 3 × 10¹⁷ cm⁻², 4 × 10¹⁷ cm⁻² and 5 × 10¹⁷ cm⁻² were applied, and scanning electron microscope (SEM) observations, energy dispersive spectroscopy (EDS) analyses, X-ray photoelectron spectroscopy (XPS) and Secondary Ion Mass Spectrometry (SIMS) measurements were performed for both nonimplanted and implanted tools. The durability tests of nonimplanted and the modified tools were performed in industrial conditions. The durability of implanted guide pads was above 2.5 times greater than nonimplanted ones in the best case, presumably due to the presence of a carbon-rich layer and extremely hard tungsten nitrides. The achieved effect may be attributed to the dissociation of tungsten carbide phase and to the lubrication effect. The latter was due to the presence of pure carbon layer with a thickness of a few dozen nanometers. Notably, this layer was formed at a temperature of 200 °C, much smaller than in previously reported research, which makes the findings even more valuable from economic and environmental perspectives.

Negative Poisson’s ratio materials (called auxetics) reshape our centuries-long understanding of the elastic properties of materials. Their vast set of potential applications drives us to search for auxetic properties in real systems and to create new materials with those properties. One of the ways to achieve the latter is to modify the elastic properties of existing materials. Studying the impact of inclusions in a crystalline lattice on macroscopic elastic properties is one of such possibilities. This article presents computer studies of elastic properties of f.c.c. hard sphere crystals with structural modifications. The studies were performed with numerical methods, using Monte Carlo simulations. Inclusions take the form of periodic arrays of nanochannels filled by hard spheres of another diameter. The resulting system is made up of two types of particles that differ in size. Two different layouts of mutually orthogonal nanochannels are considered. It is shown that with careful choice of inclusions, not only can one impact elastic properties by eliminating auxetic properties while maintaining the effective cubic symmetry, but also one can control the anisotropy of the cubic system.

Fabrication of alumina–tungsten carbide nanocomposite was investigated. Characteristics of the densification and sintering were analyzed considering both the nano-size particle starting powders and the processing stages. Different heating rates were generated during densification and consolidation with a maximal load was applied only after a temperature of 1000 °C was reached. Due to the varying dominance of different physical processes affecting the grains, appropriate heating rates and pressure at different stages ensured that a structure with submicron grains was obtained. With directly applied alternating current, it was found that the proportion Al₂O₃ (50 wt.%)–WC provided the highest fracture toughness, and a sintering temperature above 1600 °C was found to be disadvantageous. High heating rates and a short sintering time enabled the process to be completed in 12 min, saving energy and time.

This paper presents the results of the experimental research on diamond-reinforced composites with WC–Co matrices enhanced with a ZrO₂ additive. The samples were prepared using a modified spark plasma sintering method with a directly applied alternating current. The structure and performance of the basic composite 94 wt.%WC–6 wt.%Co was compared with the ones with ZrO₂ added in proportions up to 10 wt.%. It was demonstrated that an increase in zirconia content contributed to the intense refinement of the phase components. The composite 25 wt.%C_diamond–70.5 wt.%WC–4.5 wt.%Co consisted of a hexagonal WC phase with lattice parameters a = 0.2906 nm and c = 0.2837 nm, a cubic phase (a = 1.1112 nm), hexagonal graphite phase (a = 0.2464 nm, c = 0.6711 nm), as well as diamond grits. After the addition of zirconia nanopowder, the sintered composite contained structural WC and Co₃W₃C phases, amorphous carbon, tetragonal phase t-ZrO₂ (a = 0.36019 nm, c = 0.5174 nm), and diamond grits—these structural changes, after an addition of 6 wt.% ZrO₂ contributed to an increase in the fracture toughness by more than 20%, up to K_Ic = 16.9 ± 0.76 MPa·m^0.5, with a negligible decrease in the hardness. Moreover, the composite exhibited an alteration of the destruction mechanism after the addition of zirconia, as well as enhanced forces holding the diamond grits in the matrix.