Because of the dilemma that the current industrial Cu enhancement methods lead to a significant decline in conductivity and ductility, Cu matrix composites reinforced by oriented multi-walled carbon nanotubes (MWCNTs) were prepared through sintering, hot extrusion, and cold drawing. Before sintering, Ni, Cu, and Ni&Cu coatings were electroless plated on MWCNTs as the intermediate transition layer, and then they were mixed with Cu powder through a nitrogen bubbling assisted ultrasonic process. By analyzing the composition, microstructure, and formation mechanism of the interface between MWCNTs and the matrix, the influence and mechanism of the interface on the mechanical properties, conductivity, and ductility of the composites were explored. The results indicated that MWCNTs maintained a highly dispersed and highly consistent orientation in the Cu matrix. The coating on Ni@CNT was the densest, continuous, and complete. The Ni@CNTs/Cu composite had the greatest effect, while the Cu composite reinforced by MWCNT without coating had the smallest reduction in elongation and conductivity. The comprehensive performance of the Cu@CNTs/Cu composite was the most balanced, with an ultimate tensile strength that reached 373 MPa, while the ductility and conductivity were not excessively reduced. The axial electrical and thermal conductivity were 79.9 IACS % (International Annealed Copper Standard) and 376 W/mK, respectively.

Austenitic stainless steels are extensively used in mechanical engineering. The machined surface integrity has an essential influence on the stress corrosion cracking (SCC) performance of stainless steels. In this paper, the effects of multi-pass turning on the SCC susceptibility of AISI 304 austenitic stainless steel were investigated by correlating the SCC crack density to the machining-induced surface characteristics in terms of roughness, micro-hardness, and residual stress. In the multi-pass turning, the surface roughness and residual stress were the least after the double pass turning, and the surface micro-hardness was the maximum after the triple-pass turning. The SCC susceptibility was evaluated after SCC tests in boiling MgCl₂ solution. The results showed that the weakest SCC sensitivity was observed in double-pass turning 304 stainless steel, while the most susceptible SCC was found in triple-pass turning. Compared with the double-pass turning, the increase in SCC sensitivity of triple-pass turning was attributed to the larger roughness, higher micro-hardness and greater residual tensile stresses.

The effects of electroless coatings on the microstructure and composition of the interface between multi-walled carbon nanotubes (MWCNTs) and a Cu matrix and the mechanical properties and wear behavior of the resulting copper matrix composites were investigated. Ni and Cu coatings were electrolessly plated on MWCNTs and mixed subsequently with copper powder. Then copper matrix composites were prepared by sintering, hot extrusion and cold drawing processes. The results showed that MWCNTs were straight, long, uniformly dispersed and aligned in the composites. The Ni coating is more continuous, dense and complete than a Cu coating. The tensile strength, compressive strength, microhardness and tribological properties of Ni@MWCNTs/Cu composite along the drawing direction were enhanced most. The ultimate tensile strength and compressive strength were 381 MPa and 463 MPa, respectively. The friction coefficient and wear rate were reduced by 59% and 77%, respectively, compared with pure Cu samples. This study provides a new insight into the regulation of tribological properties of composites by their interface.

The machined-surface integrity plays a critical role in corrosion resistance and fatigue properties of ultra-high-strength steels. This work develops a multiphysics model for predicting the microstructure changes and microhardness of machined AerMet100 steel. The variations of stress, strain and temperature of the machined workpiece are evaluated by constructing a finite-element model of the orthogonal cutting process. Based on the multiphysics fields, the analytical models of phase transformation and dislocation density evolution are built up. The white layer is modeled according to the phase-transformation mechanism and the effects of stress and plastic strain on real phase-transformation temperature are taken into consideration. The microhardness changes are predicted by a model that accounts for both dislocation density and phase-transformation evolution processes. Experimental tests are carried out for model validation. The predicted results of cutting force, white-layer thickness and microhardness are in good agreement with the measured data. Additionally, from the proposed model, the correlation between the machined-surface characteristics and processing parameters is established.