Efficacy of cellulose acetate-based membranes for wastewater treatment has been critically evaluated. With the aim to improve efficiency, future prospects and research direction of CA based membranes are also discussed in the review.
A Semi Interpenetrating Polymer Network (semi-IPN) hydrogel was prepared and loaded with an antibiotic drug, gentamicin, to investigate the wound healing activity of this system. The semi-IPN hydrogel was synthesized by combining natural polymer cellulose nanocrystal (CNC) and synthetic polymer polyethylene glycol (PEG) and poly (N,N′-dimethyl acrylamide) (PDMAA), which was initially added as a monomer dimethyl acrylamide (DMAA). CNC was prepared from locally obtained jute fibers, dispersed in a PEG-NaOH solvent system and then mixed with monomer DMAA, where polymerization was initiated by an initiator potassium persulphate (KPS) and cross-linked by N,N′-methylenebisacrylamide (NMBA). The size, morphology, biocompatibility, antimicrobial activity, thermal and swelling properties of the hydrogel were investigated by different characterization techniques. The biocompatibility of the hydrogel was confirmed by cytotoxicity analysis, which showed >95% survival of the BHK-21, Vero cell line. The drug loaded hydrogel showed antimicrobial property by forming 25 and 23 mm zone of inhibition against Staphylococcus aureus (gram-positive) and Escherichiacoli (gram-negative) bacteria, respectively, in antimicrobial analysis. At pH 5.5, 76% of the drug was released from the hydrogel within 72 h, as observed in an in vitro drug release profile. In an in vivo test, the healing efficiency of the drug loaded hydrogel was examined on a mice model with dorsal wounds. Complete healing of the wound without any scar formation was achieved in 12 days, which revealed excellent wound healing properties of the prepared drug loaded semi-IPN hydrogel. These results showed the relevance of such a system in the rapid healing of acute wounds.
This study describes the fabrication of nanocomposites using electrospinning technique from poly lactic acid (PLA) and nano-hydroxyapatite (n-HAp). The prepared electrospun PLA-nHAP nanocomposite is intended to be used for drug delivery application. A hydrogen bond in between nHAp and PLA was confirmed by Fourier transform infrared (FT-IR) spectroscopy. Degradation study of the prepared electrospun PLA-nHAp nanocomposite was conducted for 30 days both in phosphate buffer solution (PBS) of pH 7.4 and deionized water. The degradation of the nanocomposite occurred faster in PBS in comparison to water. Cytotoxicity analysis was conducted on both Vero cells and BHK-21 cells and the survival percentage of both cells was found to be more than 95%, which indicates that the prepared nanocomposite is non-toxic and biocompatible. Gentamicin was loaded in the nanocomposite via an encapsulation process and the in vitro drug delivery process was investigated in phosphate buffer solution at different pHs. An initial burst release of the drug was observed from the nanocomposite after 1 to 2 weeks for all pH media. After that, a sustained drug release behavior was observed for the nanocomposite for 8 weeks with a release of 80%, 70% and 50% at pHs 5.5, 6.0 and 7.4, respectively. It can be suggested that the electrospun PLA-nHAp nanocomposite can be used as a potential antibacterial drug carrier for sustained drug release in dental and orthopedic sector.
This study on sustainable nanocellulose modifications for various packaging applications is driven by the global social awareness and growing demand for bioproducts to reduce the use of single-use plastics. Mixed office waste (MOW) was used as the raw material to extract cellulose nanocrystals (CNCs) via the acid hydrolysis method. The average length and diameter of the CNCs were approximately 104.08 ± 0.1 nm and 9.49 ± 0.3 nm, respectively. The crystallinity index was 87%, as confirmed using transmission electron microscopy and X-ray diffraction analysis. Coating solutions of varying concentrations were prepared by mixing CNCs with collagen hydrolysate and glycerin, and the coatings were applied to the surface of uncoated paper via a rod coating process. FTIR spectra confirmed the presence of CNCs in the coated paper. High-resolution FE-SEM images provided detailed information on the surface morphology of the coated papers. The barrier and mechanical performances of the coated paper were evaluated using the oil and grease resistance KIT, hot oil, water vapor permeability, air permeability, water contact angle, tensile index, burst index, percentage of elongation, and fold tests. All the coated paper samples passed the hot oil test and exhibited the highest KIT rating. The water vapor and air resistance values of the coated paper samples increased 14 times and 250 times, respectively, compared with the uncoated paper samples. The water contact angle of the coated paper samples increased to 99.40° from 60.13°, and the surface roughness decreased from 2.37 μm to 0.85 μm. The presence of coating also increased the tensile and burst indices by 5.28 times and 1.79 times, respectively, compared with the uncoated paper samples. No cytotoxic effects were found in the optimized coated paper, and all the samples were fully degraded within 49 days, as confirmed using the soil biodegradability test. Therefore, the coated paper can be a potential alternative to existing single-use plastics for packaging materials.
12 July 2024 in Polymer-Plastics Technology and Materials