Guosong Zeng

Prof. Guosong Zeng

Department of Mechanical and Energy Engineering, Southern University of Science and Technology, Shenzhen 518055, China

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2016 in Applied Physics Letters
Verified
Journal Article
Closed access
Guosong ZengGuosong Zeng
Guosong Zeng
CTChee-Keong Tan
Chee-Keong Tan
Nelson TansuNelson Tansu
Nelson Tansu
BKBrandon Krick
Brandon Krick
Here, we reveal a remarkable (and surprising) physical property of GaN: it is extremely wear resistant. In fact, we measured the wear rate of GaN is approaching wear rates reported for diamond. Not only does GaN have an ultralow wear rate but also there are quite a few experimental factors that control the magnitude of its wear rate, further contributing to the rich and complex physics of wear of GaN. Here, we discovered several primary controlling factors that will affect the wear rate of III-Nitride materials: crystallographic orientation, sliding environment, and coating composition (GaN, InN and InGaN). Sliding in the ⟨12¯10⟩ is significantly lower wear than ⟨11¯00⟩. Wear increases by 2 orders of magnitude with increasing humidity (from ∼0% to 50% RH). III-Nitride coatings are promising as multifunctional material systems for device design and sliding wear applications.

25 May 2024 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
FAFengchao An
Fengchao An
SZSihao Zou
Sihao Zou
JHJunhua Hou
Junhua Hou
TSTianming Sun
Tianming Sun
JLJikui Liu
Jikui Liu
WLWenjun Lu
Wenjun Lu

29 December 2022 in Inorganics
Verified
Journal Article
Open access
PDF file
HLHuiqiang Liang
Huiqiang Liang
ZYZiyuan Yan
Ziyuan Yan
Guosong ZengGuosong Zeng
Guosong Zeng
(Photo-)electrocatalytic artificial photosynthesis driven by electrical and/or solar energy that converts water (H2O) and carbon dioxide (CO2) into hydrogen (H2), carbohydrates and oxygen (O2), has proven to be a promising and effective route for producing clean alternatives to fossil fuels, as well as for storing intermittent renewable energy, and thus to solve the energy crisis and climate change issues that we are facing today. Basic (photo-)electrocatalysis consists of three main processes: (1) light absorption, (2) the separation and transport of photogenerated charge carriers, and (3) the transfer of photogenerated charge carriers at the interfaces. With further research, scientists have found that these three steps are significantly affected by surface and interface properties (e.g., defect, dangling bonds, adsorption/desorption, surface recombination, electric double layer (EDL), surface dipole). Therefore, the catalytic performance, which to a great extent is determined by the physicochemical properties of surfaces and interfaces between catalyst and reactant, can be changed dramatically under working conditions. Common approaches for investigating these phenomena include X-ray photoelectron spectroscopy (XPS), X-ray absorption spectroscopy (XAS), scanning probe microscopy (SPM), wide angle X-ray diffraction (WAXRD), auger electron spectroscopy (AES), transmission electron microscope (TEM), etc. Generally, these techniques can only be applied under ex situ conditions and cannot fully recover the changes of catalysts in real chemical reactions. How to identify and track alterations of the catalysts, and thus provide further insight into the complex mechanisms behind them, has become a major research topic in this field. The application of in situ/operando characterization techniques enables real-time monitoring and analysis of dynamic changes. Therefore, researchers can obtain physical and/or chemical information during the reaction (e.g., morphology, chemical bonding, valence state, photocurrent distribution, surface potential variation, surface reconstruction), or even by the combination of these techniques as a suite (e.g., atomic force microscopy-based infrared spectroscopy (AFM-IR), or near-ambient-pressure STM/XPS combined system (NAP STM-XPS)) to correlate the various properties simultaneously, so as to further reveal the reaction mechanisms. In this review, we briefly describe the working principles of in situ/operando surface/interface characterization technologies (i.e., SPM and X-ray spectroscopy) and discuss the recent progress in monitoring relevant surface/interface changes during water splitting and CO2 reduction reactions (CO2RR). We hope that this review will provide our readers with some ideas and guidance about how these in situ/operando characterization techniques can help us investigate the changes in catalyst surfaces/interfaces, and further promote the development of (photo-)electrocatalytic surface and interface engineering.

6 March 2024 in Nanomanufacturing and Metrology
Verified
Journal Article
Open access
PDF file
HLHuiqiang Liang
Huiqiang Liang
ZWZhenghao Wei
Zhenghao Wei
JFJiongchong Fang
Jiongchong Fang
YLYanming Li
Yanming Li
CLChangli Li
Changli Li
Guosong ZengGuosong Zeng
Guosong Zeng
The limited material removal rate of conventional chemical mechanical polishing (CMP) significantly hinders the fabrication efficiency and surface quality, thereby preventing the development of gallium nitride (GaN)-based devices. Moreover, the incorporation of photoelectrochemistry in CMP has garnered increasing attention because of its potential to enhance the quality and efficiency of the GaN process. However, a considerable gap still exists in the comprehensive understanding of the specific photoelectrochemical (PEC) behavior of GaN. Here, we report the influence of the electrolyte on the PEC etching of GaN. Various acids and bases were tested, with their pH being carefully adjusted. The concentrations of the cations and anions were also examined. The results showed that photocorrosion/photoetching was more pronounced in sulfuric acid, phosphoric acid, and nitric acid environments than in alkaline environments, but it was less pronounced in hydrochloric acid. Furthermore, the effects of pH and anion concentration on photoetching were investigated, and the results revealed that photoetching in acidic environments weakened with increasing pH levels and diminished with increasing sulfate concentration. The underlying reasons contributing to this observation were explored. These findings provide ideas for improving the photoetching efficiency of GaN, thereby enriching the photoelectrochemical mechanical polishing (PECMP) technology of GaN.

27 October 2020 in Advanced Energy Materials
Verified
Journal Article
Closed access
PDF file
TKTobias A. Kistler
Tobias A. Kistler
Guosong ZengGuosong Zeng
Guosong Zeng
JYJames L. Young
James L. Young
LWLien‐Chun Weng
Lien‐Chun Weng
CAChase Aldridge
Chase Aldridge
NDNemanja Danilovic
Nemanja Danilovic

1 March 2025 in Applied Physics Letters
Verified
Journal Article
Closed access
JCJiahe Cao
Jiahe Cao
YWYan Wang
Yan Wang
CZChuang Zhang
Chuang Zhang
GHGuofeng Hu
Guofeng Hu
Weihua TangWeihua Tang
Weihua Tang
CTChee-Keong Tan
Chee-Keong Tan
In this study, we employ first-principles calculations to explore the structural and electronic properties of monoclinic Al2O3/Ga2O3 superlattices with varied layer thickness and to perform a comparative analysis with (AlxGa1−x)2O3 alloys. Our investigation examines the lattice constants and electronic energy bandgaps of both the superlattice structures and alloys across different Al concentrations, shedding light on the intricate relationship between composition and electronic properties. The analysis on electronic properties reveals that as the number of Al2O3 monolayers in the Al2O3/Ga2O3 superlattice rises from 2 to 6 monolayers, the bandgap correspondingly expands from 5.29 to 6.43 eV. The band alignment between monoclinic Al2O3 and Ga2O3 exhibits a type-II band alignment. The conduction and valence band offsets between the bulk material and Al2O3/Ga2O3 superlattice varies with change in the number of Al2O3 monolayers. Our study gives a deeper insight into the properties of the Al2O3/Ga2O3 superlattice and suggests a solution to the Al-phase separation issue in (AlxGa1−x)2O3 alloys for advanced semiconductor device applications.