Because of the large discharge of marine diesel engines, direct measurement is difficult and complicated. In order to obtain accurate data of marine diesel engine exhaust flow, the carbon balance method is generally used for calculation, but the carbon balance method has iterative operation, adopts wet concentration calculation, and does not consider sulfur oxide components, thus resulting in errors in the calculation results. In this paper, according to the calculation model of air-fuel ratio proposed by S H Chan, the law of conservation of C, H, and O atoms is observed, sulfur oxides in the exhaust are considered, and a new exhaust flow calculation model based on air-fuel ratio is obtained. This calculation model is the first to directly use dry gas concentration in the calculation model of air-fuel ratio. Then, the simplified calculation model is obtained by ignoring CO and simplifying coefficient , the difference between the carbon balance method, ignoring CO, and the simplified model is compared, and then the exhaust flow value and exhaust density are calculated by the test data. The simplified calculation model can also calculate the mass flow rate of carbon dioxide, unburned hydrocarbon, and carbon monoxide. Finally, a software program is developed for the simplified calculation model, which is convenient for quick calculation and quick acquisition of exhaust flow data, thus laying a solid foundation for the application of the simplified calculation model in real ships.
8 July 2022 in Journal of Marine Science and Technology
Natural gas/diesel dual‐fuel engine has become an urgent need to alleviate the energy crisis and reduce emissions. As an additive, reforming gas can improve the combustion process of dual‐fuel engines because it improves the combustion rate and compensates for the low reactivity of natural gas. Therefore, it is of great significance to study the ignition characteristics of natural gas diesel blends by adding H 2 and syngas. Based on ANSYS Chemkin 17.0 software, the ignition delay time was solved by a closed uniform model. The effects of H 2 and syngas on the ignition performance of a natural gas/diesel engine were studied. The results showed that the ignition delay time of the methane/n‐heptane mixture was prolonged after adding H 2 in the range of medium and low temperatures. This was due to the fact that reaction R3 (OH + H 2 = H + H 2 O) was an endothermic reaction, which consumed OH radicals and inhibited the ignition process. In the high‐temperature range, adding H 2 reduced the ignition delay time of the mixture system, which was because of the significant increase in the sensitivity coefficients of R1(H + O 2 = O + OH) and R3 and the generation of OH radicals. Therefore, the reduction in ignition delay caused by H 2 addition in the high‐temperature regions was mainly attributed to R3 and R1. In syngas, CO reduced the ignition delay time of methane/syngas/n‐heptane. However, the addition of CO could reduce the importance of R3 in the reaction process—resulting in the weakening of the influence of H 2 on ignition delay. This study can expand the theoretical basis of ignition characteristics of methane/n‐heptane mixture with H 2 and syngas under dual‐fuel engine‐relevant conditions.
12 September 2022 in Polish Journal of Environmental Studies
Among existing diesel engines, fuel improvement through additives is an attractive option to meet increasingly stringent pollutant emission regulations for diesel engines. Because of the good REDOX properties of rare earth materials, it can improve the combustion performance of diesel engines and reduce pollutant emissions. This paper characterizes the performance of inorganic acid rare earth and organic acid rare earth and analyzes the emission reduction performance from the crystal structure, which aim to compare the effects of inorganic acid rare earth and organic acid rare earth on the emission reduction performance of existing diesel engines under similar conditions. The emission reduction performance of two rare earth fuel additives of cerium carbonate and cerium stearate in Changchai twin-cylinder direct injection diesel engine at five rotational speeds is contrastively studied. The experimental results show that two kinds of rare earth fuel additives can effectively reduce NOX, CO and HC emissions of diesel engines. And the maximum reduction rate of NOX, CO and HC in cerium carbonate is 11.37%, 14.63% and 13.80% respectively, while the maximum reduction rate of NOX, CO and HC in cerium stearate is 10.19%, 12.15% and 9.40% respectively. Cerium stearate has higher NOX, CO, HC and PM emissions than cerium carbonate due to its small specific surface area. So the emission reduction effect of cerium carbonate is better than that of cerium stearate.
Perovskite possess tunable crystal structures that enable the creation of active sites favorable for CO2 adsorption and activation through appropriate doping, while their electronic structures facilitate electron transfer during catalytic reactions. In this study, BaSnO3 was modified by substituting 4% of Ba with Mg to obtain Ba0.96Mg0.04SnO3 via a co-precipitation method. Structural and physicochemical characterization (ICP, XRD, SEM-EDS, BET) revealed that Mg doping reduced particle size, increased specific surface area by 26%, and enhanced oxygen storage capacity by 6.1%. The doped catalyst also exhibited improved thermal stability, with smaller losses in surface area and oxygen storage after 1200 °C thermal aging. CO2 adsorption tests showed higher adsorption rates and capacities, while catalytic reduction experiments demonstrated that Mg doping prolonged the catalyst’s lifetime from 24 to 40 cycles and increased maximum carbon deposition from 12.68% to 22.54%. These results indicate that Mg doping effectively enhances BaSnO3’s catalytic activity, structural stability, and durability, making Ba0.96Mg0.04SnO3 a promising candidate for CO2 thermal reduction applications.
To deal with the environmental pollution caused by diesel engine exhaust gas, this paper calls for the use of fuel additives to improve the fuel quality or combustion quality to reduce the generation of harmful components in diesel engine exhaust gas. Based on the excellent REDOX capacity of rare earth elements, rare earth hydroxide is adopted as fuel additive. Firstly, the rare earth hydroxide is prepared, the contributory factors are analyzed, and the properties are characterized. Then through the building diesel engine test platform, different concentrations of rare earth hydroxide additives (60 mg/L, 80 mg/L and 100 mg/L) are respectively added to 0# diesel oil to make three kinds of oil samples, and the comparison test is conducted to compare with 0# diesel oil. The emission reduction ability of rare earth hydroxide additives is tested by measuring the content of harmful components in diesel exhaust gas. The experimental results show that the emission reduction performance of lanthanum hydroxide is better than that of cerium hydroxide, the 80 mg/L is the optimal amount of lanthanum hydroxide additives, its maximum reduction of NOX, CO and HC emissions is 29.3%, 40.0% and 45.7% respectively, and its maximum increment of PM emissions is 9.5%. Therefore, suitable additives can be selected according to actual needs of PM emission.