The interaction effect of micro arc oxidation (MAO) parameters on the microstructure and wear properties was investigated. The results showed that the electric current and oxidation time significantly influenced the thickness and grinding crack width of the ceramic coatings within the range of the selected parameters, and the interaction effect of the electrical parameters was not obvious. The surface morphology, cross-section morphology, and element distribution of the coatings were observed using scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The results showed that ceramic coatings with γ-Al2O3 and α-Al2O3 formed, which enhanced the coating performance. After that, the microhardness and wear resistance were tested. Under the optimal process, the microhardness of a coating section was up to 1200 HV0.1, and the friction coefficient was just 0.3. When wear occurred, the volcanic microstructures experienced extrusion and deformation, and then peeled off under shear stress, which led to the formation of a grinding crack. The main failure modes of the micro arc oxidation coatings were abrasive wear and spalling failure.
13 June 2022 in Mathematical Problems in Engineering
Because of the large discharge of marine diesel engines, direct measurement is difficult and complicated. In order to obtain accurate data of marine diesel engine exhaust flow, the carbon balance method is generally used for calculation, but the carbon balance method has iterative operation, adopts wet concentration calculation, and does not consider sulfur oxide components, thus resulting in errors in the calculation results. In this paper, according to the calculation model of air-fuel ratio proposed by S H Chan, the law of conservation of C, H, and O atoms is observed, sulfur oxides in the exhaust are considered, and a new exhaust flow calculation model based on air-fuel ratio is obtained. This calculation model is the first to directly use dry gas concentration in the calculation model of air-fuel ratio. Then, the simplified calculation model is obtained by ignoring CO and simplifying coefficient , the difference between the carbon balance method, ignoring CO, and the simplified model is compared, and then the exhaust flow value and exhaust density are calculated by the test data. The simplified calculation model can also calculate the mass flow rate of carbon dioxide, unburned hydrocarbon, and carbon monoxide. Finally, a software program is developed for the simplified calculation model, which is convenient for quick calculation and quick acquisition of exhaust flow data, thus laying a solid foundation for the application of the simplified calculation model in real ships.
8 July 2022 in Journal of Marine Science and Technology
Among existing diesel engines, fuel improvement through additives is an attractive option to meet increasingly stringent pollutant emission regulations for diesel engines. Because of the good REDOX properties of rare earth materials, it can improve the combustion performance of diesel engines and reduce pollutant emissions. This paper characterizes the performance of inorganic acid rare earth and organic acid rare earth and analyzes the emission reduction performance from the crystal structure, which aim to compare the effects of inorganic acid rare earth and organic acid rare earth on the emission reduction performance of existing diesel engines under similar conditions. The emission reduction performance of two rare earth fuel additives of cerium carbonate and cerium stearate in Changchai twin-cylinder direct injection diesel engine at five rotational speeds is contrastively studied. The experimental results show that two kinds of rare earth fuel additives can effectively reduce NOX, CO and HC emissions of diesel engines. And the maximum reduction rate of NOX, CO and HC in cerium carbonate is 11.37%, 14.63% and 13.80% respectively, while the maximum reduction rate of NOX, CO and HC in cerium stearate is 10.19%, 12.15% and 9.40% respectively. Cerium stearate has higher NOX, CO, HC and PM emissions than cerium carbonate due to its small specific surface area. So the emission reduction effect of cerium carbonate is better than that of cerium stearate.
6 February 2023 in Polish Journal of Environmental Studies
As fuel additives, lanthanum and cerium are the most active rare earth elements. In order to compare the emission reduction performance of the two rare earth elements additives, lanthanum oxalate and cerium oxalate are used as the comparison objects in this paper. In order to reduce the error, it is necessary to prepare lanthanum oxalate and cerium oxalate. After lanthanum oxalate and cerium oxalate was prepared by precipitation method, a series of modern characterization methods, such as XRD, SEM, EDS and BET, are used to characterize and analyze the self-made additive powder, and the relationship between the emission reduction performance and the internal relationship is analyzed. By changing the ratio of fuel additives and carrying out the emission test on the self-built diesel engine platform, the optimal amount of additives is obtained. Fuel additives of lanthanum oxalate and cerium oxalate with a mass fraction of about 45mg/L for diesel engine is a more suitable choice. Cerium oxalate has better emission reduction performance than lanthanum oxalate. The conclusion is that reasonable use of two organic acid rare earth fuel additives can greatly reduce NOX, CO and HC emissions from diesel engines.