The flow field and the efficiency of the compressor can be improved and increased by the guide vane in the radial inlet chamber. However, the guide vane generates the wake and results in the rotor–stator interaction, which threatens the safety of the impeller. This paper investigated the guide vane with a self-induced slot (SIS) in a radial inlet, and the self-induced slot was a passive flow control method. Through computational fluid dynamics (CFD) simulation, the radial inlet containing unevenly distributed guide vanes (UGVs) in the hydrogen compressor was studied to clarify the flow phenomenon in the radial inlet and the aerodynamic load on the impellers. The simulation results showed that the self-induced slot did not affect the compressor performance but improved the pure wake style to the weak wake near the shroud region. The aerodynamic load on the impeller leading edge was obtained under different radial inlets through unsteady simulation. The dominant frequency and the pulse amplitude of aerodynamic load were obtained by fast Fourier transforms (FFTs). The SIS model had lower amplitude values at the impeller passing frequency, and the reduction in amplitude was about 18% compared to the UGV model near the impeller shroud region.

This study reconstructed the flow field of a symmetrical variable inlet guide vane in a centrifugal compressor through the passive control method of vane slots. Based on the high-fidelity numerical simulation model verified by experiments, the influence of different slot forms on the flow field was investigated, and the passive control mechanism was revealed. The results demonstrated that the vane slot method can effectively suppress the suction surface separation and broaden the range of low-loss incidence angles. Overall, the 50_30 slotted vane achieves the best flow field control, with a 65.6% reduction in the total pressure loss coefficient and a 2.3° reduction in the deviation angle, respectively, at a 25° incidence angle. The linear characteristics of the pre-swirl grade variation curve with variable inlet guide vane incidence angles are also improved. Furthermore, changing the slot outlet angle has the most significant influence on the aerodynamic performance as it changes the throat width of the location, thereby affecting the flow rate and momentum of the jet. Finally, the impact of the velocity varies in the first self-similarity region on the slotted vane. The results indicate that, in contrast to the baseline vane, the suppression effect of the slot jet on the flow separation improves with the inlet velocity, whereas the deviation angle of the slotted vane declines with the inlet velocity. Meanwhile, the higher the incoming flow velocity, the better the slotted jet can inhibition of flow separation.

One of the primary parts of a closed Brayton cycle that uses a helium–xenon mixture as the working medium is a centrifugal compressor. Nowadays, there has been minimal research on the theoretical underpinnings and design procedures of a helium–xenon mixture centrifugal compressors, and the internal flow mechanisms remain poorly understood. In this study, we present a redesign of the 15 g/mol helium–xenon centrifugal compressor originally developed by Bruno M, utilizing a helium–xenon mixture as the working fluid to enhance compressor performance and facilitate an in-depth analysis of the internal flow dynamics. The findings indicate a significant expansion of the stable operating range of the redesigned compressor under identical outlet conditions, with a 33.27% increase in flow margin and substantial improvements in the pressure ratio. Furthermore, under consistent inlet conditions, at an operational flow rate of 0.8657 kg/s, the redesigned compressor exhibits a pressure ratio that is 2.11% greater than that of the original design, along with a variable efficiency increase of 1.1%.

The annular seal between stator and rotor substantively acts as a bearing that affects the rotordynamic characteristic of the turbomachinery rotor system. The rotor wake turbulence in a canned motor Reactor Coolant Pump (RCP) will lead to inflow pressure distortion at the annular seal entrance, thus further affecting the seal rotordynamic characteristics and threatening the stable operation of RCP. In order to obtain the seal rotordynamic coefficients, a transient numerical method applies the mesh deformation technique to simulate the multiple-frequency elliptical rotor whirling orbit model. The transient solutions were proposed to solve the unsteady reaction forces of annular seals at five excitation frequencies for each case. The inflow pressure distortion patterns were simplified as harmonic functions, including two important influence parameters that are impeller blades number m and pressure fluctuation ratio $\lambda$. The numerical results showed that with nonuniform time-averaged pressure distribution at the entrance of the annular seal in Case 2, the inflow distortion significantly affects the seal rotordynamic coefficients, while the rotational spinning speed in Case 3 can weaken the time-averaged nonuniformity and accordingly make a dent in the influence. Increasing impeller blades number m and pressure fluctuation $\lambda$ both result in a sharp diminution of the negative stiffness $K_{eff}$, as well as an obvious increase in the effective damping $C_{eff}$, which will strengthen rotor misalignment and system stability. In addition, the larger impeller blades number m and higher pressure fluctuation $\lambda$ will make the effective damping $C_{eff}$ more independent of the whirling frequency. These results provide theoretical guidance for the operation safety of RCP.