Almond shell-modified urea–formaldehyde resins (AUF) were prepared in this study. The optimal addition amount of almond shells was selected by formaldehyde emission and wet shear strength. The activation energy (Ea) values at different conversion rates and the reaction kinetics were estimated based on the Flynn–Wall–Ozawa method. The results indicated that almond shells can significantly reduce the formaldehyde emission and increase wet shear strength and thermal stability of the urea–formaldehyde resin adhesive. The optimal addition of almond shells is 3 wt %.
In this work, ethyl acetate (EA) and trichloromethane (TR) extracts were extracted from Phoebezhennan wood residues and the extracts were then applied to the preparation of UV shielding films (UV-SF). The results revealed that substances including olefins, phenols and alcohols were found in both EA and TR extracts, accounting for about 45% of all the detected substances. The two extracts had similar thermal stability and both had strong UV shielding ability. When the relative percentage of the extract is 1 wt% in solution, the extract solution almost blocked 100% of the UV-B (280–315 nm), and UV-A (315–400 nm). Two kinds of UV-SF were successfully prepared by adding the two extracts into polylactic acid (PLA) matrix. The UV-SF with the addition of 24 wt% of the extractive blocked 100% of the UV-B (280–315 nm) and more than 80% of the UV-A (315–400 nm). Moreover, the UV shielding performance of the UV-SF was still stable even after strong UV irradiation. Though the addition of extracts could somewhat decrease the thermal stability of the film, its effect on the end-use of the film was ignorable. EA extracts had less effect on the tensile properties of the films than TR extracts as the content of the extract reached 18%. The results of this study could provide fundamental information on the potential utilization of the extracts from Phoebe zhennan wood residues on the preparation of biobased UV shielding materials.
24 August 2020 in Journal of Thermal Analysis and Calorimetry
In this paper, halloysite nanotubes (HNTs) are used to enhance the bonding properties and water resistance of soy protein adhesives. HNTs are modified by KH560 marked as KH560-HNTs and dispersed in the adhesive matrix by ultrasonic-mechanical combination meanly, exploring the optimal addition amount of KH560-HNTs in the adhesive matrix and preparing a nanocomposite adhesive with uniform texture and exceptional properties. The results show that KH560-HNTs can significantly improve the bonding strength and thermal stability of SPI. The optimal addition of KH560-HNTs is 2%, meanwhile, the dry and wet bonding strengths are 1.63 MPa and 1.44 MPa, which increased by 34.71% and 102.82%, respectively, compared with that of soybean protein adhesive (SPI-0). Therefore, KH560-HNTs can be used to prepare environmentally friendly and excellent performance soy protein adhesives. In addition, the results can provide a research basis for the preparation of functional soy protein adhesives by loading additives in HNTs.
In this study, different molar of methylolureas (MMU) were used to improve the properties and drying speed of the raw lacquer (RL). The drying time, gloss, pencil hardness and impact resistance of the lacquer film were tested. The thermal behaviors and chemical structures of the lacquer membrane were also discussed by thermal gravimetric analysis (TGA), fourier infrared spectrometer (FT-IR) and nuclear magnetic resonance (NMR) analysis, respectively. The results demonstrated that lower molar ratio MMU can significantly improve the properties of lacquer. The TGA analysis showed that the modified lacquer had high thermal stability than that of the control. The FT-IR and 13C NMR analysis revealed that the structures of the modified lacquer were significantly improved by cross-linking with the hydroxymethyl groups and methylene methyl ethers of MMU. In addition, through scanning electron microscopy (SEM) characterization, it was found that the introduction of MMU can effectively improve the surface smoothness of the lacquer film.