Ferroelectric polymers have great potential applications in mechanical/thermal sensing, but their sensitivity and detection limit are still not outstanding. We propose interface engineering to improve the charge collection in a ferroelectric poly(vinylidene fluoride-co-trifluoroethylene) copolymer (P(VDF-TrFE)) thin film via cross-linking with poly(3,4-ethylenedioxythiophene) doped with polystyrenesulfonate (PEDOT:PSS) layer. The as-fabricated P(VDF-TrFE)/PEDOT:PSS composite film exhibits an ultrasensitive and linear mechanical/thermal response, showing sensitivities of 2.2 V kPa−1 in the pressure range of 0.025–100 kPa and 6.4 V K−1 in the temperature change range of 0.05–10 K. A corresponding piezoelectric coefficient of −86 pC N−1 and a pyroelectric coefficient of 95 μC m−2 K−1 are achieved because more charge is collected by the network interconnection interface between PEDOT:PSS and P(VDF-TrFE), related to the increase in the dielectric properties. Our work shines a light on a device-level technique route for boosting the sensitivity of ferroelectric polymer sensors through electrode interface engineering.
Electrocaloric effect (ECE) has the potential applications in solid-state refrigeration with the features of high efficiency and environmentally friendly. Large adiabatic temperature change in a wide temperature range is needed for electrocaloric effect to meet the requirement of commercially application. In this work, giant electrocaloric effect is found in PbTiO3 nanoparticle with double-vortex domain structure in a wide temperature range by using phase field method, which the lowest and highest adiabatic temperature change (ΔT) is 7.2 K and 16.5 K, respectively. The influence of misfit strain on the ECE of PbTiO3 nanoparticle with the double-vortex domain structure is investigated, and results show that the compress misfit strain can enhance the ECE, but the tensile misfit strain reduces the ECE. This work reveals a way to obtain giant ECE of ferroelectric materials by domain engineering and strain engineering in a wide temperature range.
The influence of vortex domain switching on the electrocaloric (EC) property of a PbTiO3 nanoparticle is studied using the phase field method combined with thermodynamics analysis. The calculation results reveal that both a very large negative adiabatic temperature change (ΔT = −6.34 K) and a positive adiabatic temperature change (ΔT = 4.16 K) appear in the PbTiO3 nanoparticle when the vortex domain switches from the clockwise state to the counterclockwise state under a curled electric field. The obtained results will be of help in understanding the EC property in ferroelectrics with multidomain structure.
Diffuse phase transition was found in barium titanate (BT) thin films with a thickness of 300 nm prepared by a sol–gel method. The electrocaloric effect of these BT thin films was also investigated under a sweep electrical field of 216.7 kV cm−1. Interestingly, it was found that the electrocaloric temperature change (ΔT) increased with a decrease in temperature when the temperature was below 310 K. The novel electrocaloric phenomenon observed in BT thin films with a diffuse phase transition is significant in studying the room temperature electrocaloric effect, which is promising in the refrigeration industry.
8 May 2020 in Journal of Materials Science: Materials in Electronics
We present herein a modified cold sintering process (CSP) for BaTiO3 ceramics using a surface coating at the particle surface which could enhance the relative density of BaTiO3 up to ∼93.5% at 220 °C and 500 MPa. The surface coating greatly enhances the ceramic density, mainly because it facilitates the dissolution–precipitation process during CSP. Ba vacancies form at the surface of the coated powders, so Ba(OH)2 solution is used to compensate Ba ions in the as-cold-sintered ceramics, which increases the dielectric permittivity. Post-annealing at 700 and 900 °C increases the relative density to 97%, and the resulting relative dielectric permittivities are 810 and 1550, respectively, at room temperature and 1 kHz. This technique may also be extended to materials with very small, incongruent solubility in water or volatile solutions that use the cold sintering process.