This study aims to determine the correlation between the mean value of bone density measured on the CBCT device and the primary stability of dental implants determined by resonant frequency analysis. An experimental study was conducted on a material of animal origin: bovine femur and pig ribs. Two types of implants were used in this study: self-tapping and non-self-tapping of the same dimensions. Results of the experimental study showed a statistically significant correlation between bone density expressed in HU units and the primary stability of self-tapping and non-self- tapping dental implants expressed in ISQ units in bovine femur bones and self-tapping implants and pig rib bones. There was no statistically significant correlation between non-self-tapping dental implants in pig rib bones. Self-tapping and non-self-tapping implants did not show statistical significance in the primary stability in bones of different qualities. The analysis of bone density from CBCT images in the software of the apparatus expressed in HU units can be used to predict the degree of primary stability of self-tapping and non-self-tapping dental implants in bones of densities D1 and D2, and self-tapping dental implants in bones of the lower quality D4.

Background and Objectives: The aim of this study was to clinically evaluate the primary and secondary stability of dental implants with different macrodesigns using resonance frequency analysis and to determine whether implant design and length influence implant stability. Materials and methods: This study included 48 healthy patients receiving dental implants, and a pre-implant planning protocol was used, which involved detailed bone analysis, clinical examinations, and Cone beam computed tomography (CBCT) analysis. The implants were of various types and dimensions (Alpha-Bio Tec (Israel), DFI, SPI, and NEO), and the surgical procedures were performed using standard methods. Implant stability was measured using resonance frequency analysis (RFA) immediately after placement and after 3, 6, and 12 months. The total number of implants placed in all patients was 96. Results: The average primary stability value for 10 mm SPI implants placed in the maxilla was 68.2 ± 1.7 Implant Stability Quotient (ISQ) units, while for 10 mm NEO implants, it was 74.0 ± 0.9. The average primary stability value for a 10 mm DFI implant placed in the mandible was 72.8 ± 1.2 ISQ, while for a 10 mm NEO implant placed in the mandible, it was 76.3 ± 0.8 ISQ. Based on the Friedman ANOVA test, the differences in the stability measurements for the 10 mm and 11.5 mm SPI implants and for the 10 mm and 11.5 mm NEO implants in the maxilla on day 0 and after 3, 6, and 12 months were significant at p < 0.05. Similarly, based on the Friedman ANOVA test, the differences in the stability measurements for the 10 mm and 11.5 mm DFI implants and for the 10 mm and 11.5 mm NEO implants in the mandible on day 0 and after 3, 6, and 12 months were significant at p < 0.05 (p = 0.00000). Conclusions: Universal tapered implants of the NEO type stood out as the optimal choice, as they provided statistically significantly higher primary stability in both soft and hard bone types compared to other implants. The implant length did not significantly affect this stability.

Introduction/Objective. Bone resorption is a common problem in dentistry, and bone reparation cannot be easily achieved. Several techniques of bone grafting and the use of low-level laser treatment (LLLT) as a new therapeutic optional recommended for improving bone repair were applied. The aim of the study was to investigate the influence of LLLT in bone repair of artificially made bone defects in the rat mandible using histomorphometry. Methods. The research was carried out on 60 female rats. Bone defects were made in the mandible, and animals were divided into two groups, each containing 30 animals. In the study group, the implantation site was submitted to GaAlAs laser irradiation 670nm, 5 mW, 4 min/per day for 5 days. The control group had no postoperative treatment. Animals were sacrificed after two, six, and eight weeks post LLLT, and preparations were analysed by histomorphometry, determining bone area fraction, bone area, integral density, mean density, and density variation. Results. Histomorphometric analysis revealed statistically higher values of area fraction, area, and integral density in the study group after two and six weeks. However, no beneficial laser effect was noticed after eight weeks. Conclusion. Low-level lasers have a stimulating effect on reparatory mechanisms in the early regeneration stage of artificially made bone defects in the rat mandible and can be used as a useful helping method in bone treatment.

Introduction. A dentigerous cyst is a pathological lesion associated with the crown of the unerupted or impacted tooth. Decompression is proposed as the initial treatment for large cysts, especially in younger patients. The aim of this study was to present clinical, radiological, histopathological, and therapeutical aspects of the large dentigerous cyst in the maxilla. Case report. A 12-year-old boy with a large dentigerous cyst in the maxilla was referred to our clinic. A dentigerous cyst was associated with the crown of the unerupted maxillary left canine. Management of the cyst included initial decompression with biopsy, followed by secondary enucleation after 9 months and orthodontic treatment. Histopathological examination confirmed the definitive diagnosis of the dentigerous cyst. Conclusion. Initial decompression with a subsequent enucleation proved to be an effective treatment of choice for the large dentigerous cyst.